West JerusalemIrrigation deep well pumpThere is no market after laying eggs under the nest

West JerusalemZD slurry pump,

　　During the process, the equipment must be regularly maintained and overhauled to avoid blockage. As the name suggests, but in fact, we use it at ordinary times　　Body. So that the pump can realize high concentration transmission without auxiliary devices. The unique sealing device can effectively balance the pressure inside and outside the oil chamber, so that the pressure at both ends of the mechanical seal can be kept balanced, which maximizes the reliable operation of the mechanical seal and greatly extends its service lifeWest Jerusalem, which are padded with green paper or asbestos. There is a gap of .- mm between the rear gland and the bearing.Puzhibulam,　　It, generator and market formed at the beginning of construction have gradually formed a certain scale after more than ten years of rapid development. In the early stage, in order to meet the needs of market development, generators and other mechanical and electrical products were collectively moved to the phase II market for operation. With a good business environment, water pumps and generators　　After understanding the working principle of the submersible slurry pump, we will also know that those parts are prone to wear during normal use. In this way, we can carry out targeted anti-corrosion and wear-resistant treatment on these parts during optimization, so as to improve the integrity of the equipment and　　Fourth, model selection parameters: outlet diameter, flow, dust, motor power, pumping rate,West JerusalemSubmersible non clogging sewage pump, maximum particle and weight.

　　No matter what type of slurry pump you need, Ritter pump will provide you with the highest quality slurry pump products; The latest development of submersible slurry pump technology in recent years The diving depth has increased from meters to meters!　　. Generally, the moisture absorption section exceeds the suction section of the pump (the pump head is damaged). When the breathing tube passes through the pipe, the axial force cone tube shall be selected.　　Second, the power used is not matched, so the motor temperature will be too high after long-term overload operation; In addition, frequent startup during use will also lead to fever, so Itechnical service,　　 Why does the demand for submersible slurry pumps increase greatly? From the perspective of market demand, although the number of submersible slurry pumps has not exceeded that of vertical slurry pumps,West JerusalemSelf priming non clogging sewage pump, it has a rapid development momentum. The main reason is that the above-mentioned use is convenient and flexible; In addition, the application market of submersible slurry pump is also better than that of vertical pump　　If there is a standby pump, it is recommended that the two pumps be used in turn. When the equipment is in use, it can pretend that a filter screen plays the role of filtration, so as to avoid a lot of impurities entering the equipment and causing pump jamming.　　 Assembly of rotor parts of submersible slurry pump Before assembly, apply a layer of lubricating oil on the mounting surface to protect the shaft hole from damage.

　　When the pump is not in use, the pump shall be lifted away from the water source in time to drain the accumulated water in the pump, especially in cold winter. Then put it in a dry place. Conditional users can also apply oil to the key parts of the water pump and add lubricating oil to the bearing to prevent parts from rusting. in additionInterpretation and observation, mixing impeller and other main flow passage parts are made of high wear-resistant raw materials, which are wear-resistant, corrosion-resistant, non clogging, and have strong sewage discharge capacity, and can effectively pass through large solid particles. It is not limited by suction range with high slag suction efficiency and more complete desilting. There is no need to equip auxiliary vacuum pump, during the design of the slurry pump and the investment is lower.　　In order to facilitate the disassembly of the impeller, the impeller is connected with the pump shaft through reverse buckle. This is why the impeller will be turned off when installing a new slurry pump. Therefore, we must pay attention to the impeller marked on the pump body during preliminary installation and use　　 In addition, the noise method directly detects the noise of the equipment in the detection process, but this measurement will also be affected by the surrounding noise, so in fact, this measurement is not very accurate.West Jerusalem,　　Different process requirements: the motor used in the vertical slurry pump is an ordinary vertical motor, which has no waterproof . The motor of the submersible slurry pump and the pump shaft are coaxial. The motor shall be waterproof and sealed. The motor and the pump body can invade underwater at the same time.　　In addition to the main impeller inside the equipment, a set of impeller for mixing will be added at the bottom of the equipment, so that some mortar slowly settled inside the equipment can be mixed with water to become a flowing medium, so that the equipment can be used without its　　Carbon building materials, chemical industry and other industrial industries are mainly used to transport abrasive pastes containing solid particles.