JiningGuide rail hydraulic lifting platformIntelligent operation

Although lifting cargo elevators have good safety, if we do not pay attention to detailed maintenance, accidents may occur. Therefore, we should pay attention to them when performing daily maintenance.Check the hydraulic oil quality and level. When the lifting platform is raised to a high position, the hydraulic oil level should be - millimeters higher than the bottom of the oil tank. When the color of the hydraulic oil darkens, or there are foreign objects such as gravel in the oil, the hydraulic oil should be replaced in a timely manner. The hydraulic system of the lifting platform should be checked for hydraulic and pipeline connections. If the pipeline is damaged, it should be replaced immediately; When there is looseness in the connection part, tighten the pipe joint.Jining,Many people believe that the mechanical strength of the elevator itself is relatively high when using it, so they did not strictly follow the installation method specified in the manual during the installation process. Little did they know that this would cause increased wear and tear of the parts and inflexible operation. In addition, they should pay attention to the installation precautions corresponding to the working environment and not be careless. Proper installation, use, and maintenance of elevators are important steps to ensure the normal operation of mechanical equipment. Therefore when installing the elevator, please be sure to strictly follow the installation and use related matters below, and carefully assemble and use it.Drain and discard the hydraulic oil from the hydraulic lifting cargo elevator. For the outdoor guide rail elevator, tighten the joint and remove the oil filter. After cleaning,Novice operators should pay attention to which equipment wears quickly when operating mobile elevators: Due to factors such as the processing and installation of high-altitude work platform equipment components such as mobile elevators and then return it to the oil tank and connect the pipeline.Veliko Turnovo, the equipment surface is rough, the area is small, and the load bearing is uneven, which can cause equipment wear. During the operation of high-altitude work platform equipment such as mobile elevators, the concave and convex parts on the surface of the parts are embedded and friction with each other, and metal debris undergoes secondary friction with the equipment, which will accelerate the wear and tear of the surface of the equipment parts. Therefore, mobile elevators and other high-altitude work platform equipment are prone to wear and tear of components during the running-in period, with a fast wear rate.Operating cost advantage: Low failure rate. Due to the use of advanced hydraulic systems and good methods, the failure rate of elevator operation can be minimized. Low power consumption: When the hydraulic elevator descends, it is driven by the pressure generated by its own weight, which greatly saves energy.Any product always has a break-in period when it is first used, so what precautions should we pay attention to during the break-in period when using a hydraulic lifting platform? Today, the editor will share this topic with everyone.

How to maintain elevators in winter is one reason and the primary reason. Many workers in other industries do not know that hydraulic elevators use different types of hydraulic oil in summer and winter. Often, at low temperatures, the hydraulic oil used in summer can become, it is important to remember to replace hydraulic oil containing antifreeze, which is suitable for working at low temperatures.Secondly, there should be no dirt on the friction surface. If there is any dirt, it needs to be washed off with gasoline or thinner; The reduction gearbox, gearbox, external meshing gear, and other parts of the equipment, as well as the hydraulic oil, must be tested according to the requirements in the table; The correct maintenance method for hydraulic guide rail elevators is to regularly check the steel wire ropes in various parts for any breakage or looseness. If this phenomenon is found, it should be replaced in a timely manner. The maintenance of the steel wire ropes must be strictly carried out in accordance with the specifications; Check the connection status of each part according to the braking regulations. If there is any looseness, it should be tightened in a timely manner. The tightness of the connecting bolts of the equipment should be checked when the body is under pressure. All connecting shafts should be equipped with split pins; According to regulations, check the normal operation of each mechanism, whether there is noise or malfunction, and promptly eliminate all faults; When installing, disassembling, and adjusting the rotating mechanism of the equipment, it is important to ensure that the centerline of the reducer and gear is parallel and the meshing clearance is appropriate; Regularly conduct a comprehensive inspection of the equipment to check if there is any damage to the wires and cables, and if there is any overheating of the motor. Replace and eliminate the fault in a timely manner before continuing operation; Ensure the bearings of the motor, and ensure that all boxes, distribution boxes, and brushes are properly protectedThe second is that the steel will have obvious thermal expansion effect at low temperature. Although this property of steel will be taken into account when designing and manufacturing hydraulic elevators, the environment is different after all. Under low conditions, the steel will have some unstable performance, such as hardness increase, toughness decline, etc. At this time, more attention should be paid to the maintenance of equipment to keep key parts to avoid dry grinding.Project scope,JiningType hydraulic lifting platform, tighten the joint and remove the oil filter. After cleaning, clean it with compressed air, and then return it to the oil tank and connect the pipeline.What are the advantages of installing a guide rail type elevator for goods? The advantages of civil engineering are easy to install: there is no need for a machine room above the shaft, and the top layer can be installed at a height of more than meters. The computer room can be located within a radius of meters of the shaft, occupying an area of only - square meters. The hydraulic elevator is not equipped with a counterweight device to improve the utilization rate of the shaft area. The load and load cylinder of the hydraulic elevator directly act on the foundation pit,Jininghydraulic lift, and the strength requirement for the shaft is low. A brick structure or brick concrete structure shaft is sufficient.

What should I pay attention to when starting a new mobile elevator? High priced and various specifications of scissor lift manufacturers welcome scrap merchants, industrial companies, enterprises, and power departments to visit and negotiate with the company!offerAluminum alloy elevators, also known as aluminum alloy lifting platforms, currently have a wide variety in the Chinese market. They are highly favored by users due to their flexible movement, light weight, and small size.Many people believe that the mechanical strength of the elevator itself is relatively high when using it, so they did not strictly follow the installation method specified in the manual during the installation process. Little did they know that this would cause increased wear and tear of the parts and inflexible operation. In addition, they should pay attention to the installation precautions corresponding to the working environment and not be careless. Proper installation, use, and maintenance of elevators are important steps to ensure the normal operation of mechanical equipment. Therefore, when installing the elevator, please be sure to strictly follow the installation and use related matters below, and carefully assemble and use it.Carefully prepare a special construction plan for installation and provide technical disclosure to the installation personnel. Our company has been engaged in various types of scissor lift manufacturers and other materials for years,JiningSelf propelled hydraulic lifting platform, and operates with integrity. Welcome to call!Jining,The explanation mainly focuses on the mechanism of lifting platforms, and now there are many different types of lifting platforms. In order to better use lifting platforms, we have started to develop different industries using different lifting platforms. Electric lifting platforms have become the main product of small lifting platforms. They are small in size, light in weight, practical in appearance, easy to move, stable and free in lifting, large in load capacity, and large in plane area, and lifting equipment is used in enterprises of all sizes so the use of lifting platforms is necessary.The inconsistent production dimensions of the hydraulic lifting platform support rods are a quality defect of the lifting platform equipment itself. It is recommended that the manufacturer replace them, as the probability of this situation occurring is relatively low.Avoid, especially during storage. Store in a cool and dry place, and avoid rainy and snowy weather during work.