SaganRubber lining submerged slurry pumpDefense against varying degrees of chemical variation

it can transport the slurry

　　Under the action of auxiliary devices and because the sealing device itself is special, so that the pressure at both ends of the equipment can be balanced during normal use　　 Inspection before installation: Check the specification, size and quality of thick and thin accessories.Sagan,　　 Realize centralized management. In the application of multiple fire pumps, the deployment of fire pumps may be decentralized, and the working environment of fire pumps is often complex, with operation　　Therefore, the stator winding will be burnt out due to excessive temperature rise.Tuyen Quang　　Body. So that the pump can realize high concentration transmission without auxiliary devices. The unique sealing device can effectively balance the pressure inside and outside the oil chamber, so that the pressure at both ends of the mechanical seal can be kept balanced, etc., and handle it at any time.　　The water slurry pump is a widely used equipment. Many people are interested in the water diversion and exhaust method of the slurry pump equipment. Now let&#;s talk about the water diversion and exhaust method of the submersible slurry pump: the submersible slurry pump needs to pump out the water to form a vacuum, and then supply water,

　　Some impurities will entangle the impeller, so generally, the open impeller will be used, so there is no need to worry about getting stuck in the process of transporting sewage.　　Solution: replace the remote pressure gauge; Replace the pressure transmitter; Check the connecting signal wire.　　If the pump outputs more medium liquid it will certainly do more work. If it sends less water, it will certainly do less work,SaganSplit vertical pipeline pump,　　 Protective packing of shaft seal the shaft seal pump shall regularly check the sealing water pressure and water volume, keep a small amount of cleaning water flowing along the shaft, regularly adjust the packing gland, check the packing and regularly replace the packing. The shaft seal water pressure and water volume shall meet the above (shaft seal inspection) requirements.　　When the slurry pump is working, the pump needs to be placed on land, the suction pipe in water, and the pump needs to be started. Due to the structural limitations of the mud pump and submerged slurry pump, the motor needs to be placed on the water surface during operation, and the pump must be fixed when it is put into the water. Otherwise, the motor will fall into the water　　When the submersible slurry pump works, the pump needs to be placed on land, the suction pipe needs to be placed in water, and the pump needs to be started. Due to special structural requirements, when the slurry pump motor is submerged in the water, the slurry pump and submerged slurry circulating pump need to be placed above the water surface, so they need to be fixed, otherwise the motor will fall into the water

　　Wheel, mixing impeller and other main flow passage parts are made of high wear-resistant raw materials, which are wear-resistant, corrosion-resistant, non clogging, and have strong sewage discharge capacity, and can effectively pass through large solid particles. It is not limited by suction range, with high slag suction efficiency and more complete desilting. There is no need to equip auxiliary vacuum pump, and the investment is lower.Manufacturing cost,　　Circumference. In the application of slurry pump,SaganSubmersible slurry pump, we must pay attention to reasonable design, correct calculation and appropriate type selection, which are very important. In addition to the main wheel, a set of stirring impeller is added at the bottom of the product, which can spray the precipitated slag into a mixture of water and solid particles　　 Packing shaft seal: the packing shaft seal is the most common seal, with simple structure, convenient maintenance and low price. However, the shaft seal water must be used. For the working conditions that are not suitable for the auxiliary impeller shaft seal, the packing shaft seal can be used.　　Head refers to the energy obtained from the pump by the unit weight of liquid output by the pump, so head refers to the effective energy obtained from the liquid output by the pump in unit time - that is, the effective power of the pump: the equation is PE= ρ GQH (W)= γ QH (W)Sagan,　　First, let&#;s talk about the familiar vertical slurry pumps. Here we refer to ZJL and SP submerged slurry pumps. Strictly speaking,SaganISG single stage vertical pipeline pump, the submersible slurry pump is also a vertical slurry pump, because its axis is basically vertical when it works, but it can be completely immersed in water when it runs, so it is a good choice　　It can also be used for cooling and lubrication. Once the temperature in the water pump is too high, the pump shall be stopped immediately for maintenance. Otherwise, the excessive temperature will not only affect the wear of small parts inside the equipment, but also seriously affect the working efficiency of the equipment. So what is the reason for the high temperature of the equipment　　 When the power supply voltage is too low, the pump will be overloaded, because the pump is also widely used in many rural watering. In this case, it may be lower than the rated voltage, so the current in the stator winding will also be