Ostholt2 ton lifting cargo elevatorWhat are the factors related to the price?

Frequently check whether the various mechanisms are operating normally and whether there is any noise. If a fault is found, so it should not be careless. Moreover, from a professional point of view, there are relevant rules and requirements, and you should refer to the specification manual so that you can have a correct understanding and know how to achieve better cleanliness.Ostholt,Seat belts Seat belts must be inspected once every six months, and they must be inspected or replaced by relevant units. It is strictly forbidden to use seat belts that have expired. When working in the following environments, you should wear seat belts: In the scene where high-altitude operations are required, when entering the workplace , Workers must wear safety belts; when working at heights exceeding two meters,OstholtConstruction site lifting and cargo elevator lifting, they must wear safety belts; in working environments where scaffolding is not used or there is no fence on the scaffolding, safety belts must be used when the working height exceeds meters; Safety belts must be used when working on the roof; on the top floor of a flat house, safety belts must be used when there is no protective fence within meters from the edge of the roof or the roof opening; the platform or workbench is in a suspended state; Safety belts must be used if there are openings on the ground near the roof or ladders; safety belts must be used when working at heights without safe fall prevention measures.If the motor of the hydraulic lift is overheated, stop the machine in time and continue running after troubleshooting. The motor bearings must be in good condition.CeadarLunga,OstholtRail freight elevator,It is strictly forbidden for personnel to take the freight elevator to go up and down floors and climb.Naturally connect the motor to the lift. When connecting, it must be ensured that the concentricity of the output shaft of the elevator is consistent with that of the input shaft of the motor and that the outer flanges of the two are parallel. If the concentricity is inconsistent, it will cause the motor shaft to break or the elevator gear to wear.The motor winding is short-circuited. When a short-circuit fault occurs in the motor winding, the short-circuit current is much larger than the normal operating current, causing the winding to overheat and even burn out.

The wrong connection of the motor of the elevator When a coil, coil group or one-phase winding is reversed, it will cause a serious imbalance in the three-phase current and cause the winding to overheat.Cleaning and keeping it clean is the first priority. Regularly clean up the dust or sundries on the motor of the hydraulic lifting platform, otherwise the long-term accumulated dust will fall into the motor fan, and it will be very difficult to run,OstholtFixed hydraulic lifting cargo elevator, just like the laptop we usually use. If the dust on the computer fan is not cleaned, the computer will not be easy to dissipate heat, or even buzz. It will be much better after cleaning, and the same is true for the motor of the hydraulic lifting platform. V or V; how to properly maintain the motor of the hydraulic lifting platform to avoid the motor, of course, it is safer to keep away from the water for things related to electricity, do not use it outdoors in rainy and snowy weather, etc., and pay attention to the selection during storage The environment is clean and dry; it is strictly forbidden to overload the hydraulic lifting platform. When using the hydraulic lifting platform, it must not be overloaded, which will bring a burden to the motor, and it may burn out the motor; At this time, you may wish to consult the manufacturer about the overload protection device. The overload protection device is generally selected by the manufacturer. After adding this device, you don’t have to worry about whether it is overloaded during use. It is not too expensive to add this device. Safe, more at ease); can not adjust the overflow valve (also known as 'solenoid valve')The hydraulic lifting platform can be divided into: four-wheel mobile type, two-wheel traction type, car modified type, car type, auxiliary self-propelled type, and the lifting height ranges from a meter to s meter.technical service,This kind of fixed lifting equipment can also be used in the warehouse. For example, a certain floor in the warehouse needs to be lifted to send goods or personnel into the designated warehouse.The load of this series of products is divided into . to . tons, and can also be customized according to user requirements, with a load of up to tons.Outriggers: mechanical outriggers, hydraulic outriggers, ordinary hand-operated outriggers, pull-out outriggers.

This kind of fixed lifting equipment can also be used in the warehouse. For example,Always check all wires and cables for damage. The damaged part should be bandaged and replaced in time.What should be paid attention to when starting a new mobile lift?Test the freight elevator every day to see if the freight elevator can operate normally.Ostholt,Are the water cooling and air cooling of the hydraulic station the same?Secondly, there must be no dirt on the friction surface. If there is dirt, it needs to be washed off with gasoline or thinner; the gear box, gearbox, external gear and other parts of the equipment and the hydraulic oil must be in accordance with the requirements in the table; Correctly maintain the hydraulic guide rail lift. Regularly check whether the wire ropes in each part are broken or loose. If this phenomenon is found, replace them in time. If there is any looseness it should be tightened in time. The connecting bolts of the equipment should be checked for tightness when the body is under pressure. All connecting shafts should be equipped with cotter pins; check whether each mechanism is operating normally, whether there is noise or failure , to eliminate all faults in a timely manner; when installing, dismantling and adjusting the slewing mechanism of the equipment, it is necessary to pay attention to the parallelism between the reducer and the center line of the gear, and the appropriate meshing gap; conduct a comprehensive inspection of the equipment regularly, whether the wires and cables are If there is damage, whether the motor is overheated, replace it in time and continue to run after troubleshooting; ensure that the bearings of the motor, distribution box and brushes must be kept clean, and the travel switch points of each safety device must be safe and reliable.The hydraulic lifting platform is widely used in the maintenance of industrial and mining enterprises, municipal construction and decoration of hotels and hotels, with reliable quality and perfect performance.