SacramentoThree ton cargo elevatorWhy is it so popular

When installing, dismantling and adjusting the slewing mechanism, care should be taken to ensure that the centerline of the slewing mechanism reducer is parallel to the centerline of the gear, the meshing surface is not less than %, and the meshing clearance is suitable.Frequently check the humidity of the aerial work vehicle that is prone to water accumulation. It is inevitable that the aerial work vehicle is driving in rainy and snowy weather, or on muddy roads. The bottom and some gaps and indoor floors are easy to accumulate sludge. If the owner does not clean it in time, this will hide the moisture. Therefore, the outer edge of the wheel hub, the door, the corner of the bottom of the trunk, the key hole and the wiper frame and other areas should be checked regularly, and the drainage holes in the door and various parts should be kept unblocked to ensure that the car seat covers, carpets and floors are protected from humidity. Rusty fittings.Sacramento,The opening system of the manual hydraulic stacking platform truck is divided into pedal type and manual type for selection, which is simple and easy to operate. The models are divided into fixed and mobile forks, and there are many options for ordinary legs and straddle legs. It is very suitable for warehouse,SacramentoFreight elevator lifting, and extraction.Whether it is used outdoors or indoors, some small problems will inevitably appear after a long period of time. At this time, what we should do is to maintain and maintain the elevator. How to follow the steps correctly It has become a difficult problem, and I will answer it with you.Rize,The hydraulic lifting platform is widely used in the maintenance of industrial and mining enterprises, municipal construction, and decoration of hotels and hotels, with reliable quality and perfect performance.Low cost: The cost is much lower than that of the scissor-type mobile lifting platform, so when purchasing a lifting platform, you must consider the scope of use of the lifting platform, the frequency of work,SacramentoThe cargo elevator is, the load and other factors to choose a lifting platform that suits the work requirements .The cleanliness of the hydraulic station is an important aspect of the elevator hydraulic station, so it should not be careless. Moreover, from a professional point of view, there are relevant rules and requirements, and you should refer to the specification manual, so that you can have a correct understanding and know how to achieve better cleanliness.

Regarding the cleanliness of the hydraulic station, is there any relevant rule requirement?Fixed boarding bridge: The fixed boarding bridge is a special auxiliary equipment to realize the fast loading and unloading of goods. Its height adjustment function uses a bridge between the truck and the cargo platform of the warehouse, and the forklift is moved and the goods are loaded and unloaded in batches inside the truck. , Only one person is required to operate, and the rapid loading and unloading of goods can be realized. It enables enterprises to reduce a lot of labor, improve work efficiency and obtain greater economic benefits.Whether it is used outdoors or indoors, what we should do is to maintain and maintain the elevator. How to follow the steps correctly It has become a difficult problem,Hydraulic pump station: special pump station for domestic lifting platform protection device outside the pump station imported from Italy: organ m type, mesh type, iron plate seal type.Goods should be stacked on the platform and not tilted. When the freight elevator goes up and down beyond the range of the platform, no one should stand around to watch.When the freight elevator breaks down, professionals should be invited to repair it, and the freight elevator cannot be altered without authorization.

The motor winding is short-circuited. When a short-circuit fault occurs in the motor winding, the short-circuit current is much larger than the normal operating current, which increases the copper loss of the winding,Test the freight elevator every day to see if the freight elevator can operate normally.The lifting platform needs to be placed in a ditch position, and the corresponding anti-slip work should be done; remove the gear box of the equipment, remove the shaft holding oil box, take out the lower tile and oil absorber; test the car slowly and check whether the surface around the shaft holding diameter is severely damaged ; If the damage is serious and the tungsten gold is occupied, it should be smoothed with oilstone; under the motor, and the sleeper is carried on the edge of the ditch inside the rail, and the motor is regularly pulled by a jack to remove the upper tile; the important part of the lifting platform How to deal with equipment damage Check the status of the bearing bush and oil absorber, investigate the cause of damage, replace the bearing bush, clean the shaft oil box; after assembling all parts,SacramentoFactory freight elevator lifting, install a new oil absorber on the oil box for the shaft, and in serious cases, the axle box and the wheel set will be fixed together, affecting the operation of the equipment.Regarding the cleanliness of the hydraulic station, is there any relevant rule requirement?SacramentoWhether it is used outdoors or indoors, some small problems will inevitably appear after a long period of time. At this time, what we should do is to maintain and maintain the elevator. How to follow the steps correctly It has become a difficult problem, and I will answer it with you.The motor connection is wrong. When the delta connection motor is wrongly connected into a star shape, the motor still runs with full load, and the current flowing through the stator winding will exceed the rated current, and even cause the motor to stop by itself. If it overheats it will burn out. When the star-connected motor is wrongly connected into a triangle, or the motor with several coil groups connected in series to form a branch circuit is connected in parallel with two branches, it will cause the winding and core to overheat, and in severe cases, the winding will be burned.As for the guide rail elevator installed outdoors, it is often exposed to rain and sunlight, so special attention should be paid to regular maintenance and inspection to avoid accidents.