BiawestockLifting cargo elevator 3 tonsPlay the pillar role in the industry

Secondly, there must be no dirt on the friction surface. If there is dirt, it needs to be washed off with gasoline or thinner; the gear box, gearbox, replace them in time. If there is any looseness it should be tightened in time. The connecting bolts of the equipment should be checked for tightness when the body is under pressure. All connecting shafts should be equipped with cotter pins; check whether each mechanism is operating normally, whether there is noise or failure , to eliminate all faults in a timely manner; when installing, dismantling and adjusting the slewing mechanism of the equipment, it is necessary to pay attention to the parallelism between the reducer and the center line of the gear, whether the wires and cables are If there is damage, whether the motor is overheated, replace it in time and continue to run after troubleshooting; ensure that the bearings of the motor, each box, distribution box and brushes must be kept clean, and the travel switch points of each safety device must be safe and reliable.Low cost: The cost is much lower than that of the scissor-type mobile lifting platform, so when purchasing a lifting platform, you must consider the scope of use of the lifting platform, the frequency of work, the load and other factors to choose a lifting platform that suits the work requirements .Biawestock,What safety tools are there on mobile lifts Explosion-proof valves: often seen in large hydraulic equipment, especially heavy equipment, the main effect can prevent the oil circuit from bursting or the pressure of the oil circuit is too high to cause problems with the equipment. Regarding small lifts The installation of explosion-proof valves depends on the needs of customers, but large-scale equipment basically needs to be installed.The boxes and distribution boxes of the hydraulic lift are always kept clean, and the dust on the electrical equipment is cleaned in time.Braslaw,The safety device and application of the guide rail hydraulic lifting platform The use of the guide rail hydraulic lifting platform The guide rail hydraulic lifting platform is a non-scissor hydraulic lifting freight elevator. It is used for goods between different floors of industrial plants, restaurants, restaurants, etc. The low height can be made to -mm. The advantage is that it can be placed directly on the ground without digging pits, reducing engineering construction costs, and there is no need to set up hanging points on the top, which is safe. Reliable; the hydraulic lifting platform adopts hydraulic transmission mode, and can be non-calibrated according to customer needsSeveral types: Motor winding open circuit. When one of the motor windings is disconnected, or one of the parallel branches is disconnected, the three-phase current will be unbalanced and the motor will overheat.When installing, dismantling and adjusting the slewing mechanism, care should be taken to ensure that the centerline of the slewing mechanism reducer is parallel to the centerline of the gear, the meshing surface is not less than %, and the meshing clearance is suitable.Ensure good power supply at the installation site, install a separate distribution box,BiawestockSmall cargo elevator, and the leakage switch must meet the requirements for construction elevators when used in the distribution box. If the construction elevator installed is frequency conversion, the leakage switch should be adapted to the frequency converter when selecting the leakage switch .

The design of the hydraulic lifting platform is unreasonable. When the designer designs the cylinder barrel and rod if there is a problem with the design size and angle, then there will definitely be problems in the later stage. Therefore, it is necessary to confirm the technical strength of the manufacturer when working on a hydraulic lifting platform; what is the problem with the sound of the oil cylinder of the hydraulic lifting platform? Design drawings to make, the angle of the oil cylinder is slightly deviated, it will cause the friction between the cylinder barrel and the rod, which will cause the sound; the seal quality of the hydraulic lifting platform is different, and the use of different seals will also affect the sound of the oil cylinder, and long-term wear and tear may scratch the oil cylinder and cause oil leakage, so when the hydraulic lifting platform is used,BiawestockHydraulic lifting cargo elevator, pay attention to ask the manufacturer what brand and material the seal is used; In some cases of mechanical running-in, and there will still be noises. If there is no problem after investigation, then don’t worry. It’s just a running-in problem between mechanical parts. It will disappear naturally.How to maintain the elevator correctly and replace the hydraulic oil of the elevator regularly: the hydraulic oil used in the elevator is divided into winter and summer. It is not noticed until the hydraulic cylinder of the elevator is working abnormally.Outriggers: mechanical outriggers, hydraulic outriggers, ordinary hand-operated outriggers, and start with the preparation work to prevent all possible failures and accidents. I hope that the editor can summarize the knowledge points today. Help everyone.Brake operators of various mechanisms on the equipment should regularly check and adjust the gap between the brake shoe and the brake wheel to ensure flexibility and reliability. Long-term promotion of freight elevator factory, old brand, price advantage, quality guaranteed!Always check all wires and cables for damage. The damaged part should be bandaged and replaced in time.

System: explosion-proof electronic control system, remote control system, P IC system.Honest management,Today, the editor will talk about a series of safety devices and their uses on the guide rail hydraulic lifting platform.Familiar with the use process and there is no doubt that this is the first to bear the brunt. There are two ways to understand the content that needs to be understood: one is the instruction manual provided by the manufacturer when the hydraulic lifting platform leaves the factory, which needs to be read carefully; the other is the equipment to be installed, hydraulic The lifting platform will send a professional installer to install it, and after the installation is completed, the relevant users will be trained on the operation process and safety precautions of the hydraulic lifting platform and some matters for future maintenance will also be explained; the running-in period of the hydraulic lifting platform What items should be paid attention to Check the wear of parts Newly processed and assembled parts have subtle deviations in shape and size and need a period of running-in. During the running-in period, attention needs to be paid to whether there is excessive wear and tear. High prices and various specifications Freight elevator factory has timely supply and high cost performance. It has become the preferred brand of many wire products. Welcome to buy! If you haveThe manufacturer handles it to avoid equipment failure; work between the pins and bearings to ensure that, to avoid wear, you can add some oil or butter; confirm whether there is noise. During the running-in period, it is found that the hydraulic lifting platform has noise during operation You don’t have to worry about it in the early stage. If there is no major problem, run it a few more times. After running in, the noise will naturally disappear. But if there is noise for a long time and there is no sign of fading, please be sure to solve it by the manufacturer in time; check the parts regularly Check whether it is loose before use whether there are any signs of looseness in the screws, nuts, retaining springs, backstops, oil pipe joints, etc. If there is any sign of looseness, please reinforce or replace it in time to avoid accidents.The design of the hydraulic lifting platform is unreasonable. When the designer designs the cylinder barrel and rod, if there is a problem with the design size and angle, then there will definitely be problems in the later stage. Therefore, it is necessary to confirm the technical strength of the manufacturer when working on a hydraulic lifting platform; what is the problem with the sound of the oil cylinder of the hydraulic lifting platform? Design drawings to make, the angle of the oil cylinder is slightly deviated, it will cause the friction between the cylinder barrel and the rod, which will cause the sound; the seal quality of the hydraulic lifting platform is different,BiawestockThree story cargo elevator, and the use of different seals will also affect the sound of the oil cylinder, and the seal with excellent material The continuous friction between the parts and the cylinder wall will cause the sound to be very loud, and long-term wear and tear may scratch the oil cylinder and cause oil leakage, so when the hydraulic lifting platform is used pay attention to ask the manufacturer what brand and material the seal is used; In some cases of mechanical running-in, it is not ruled out that the above three situations are normal, and there will still be noises. If there is no problem after investigation, then don’t worry. It’s just a running-in problem between mechanical parts. It will disappear naturally.Biawestock,Regarding the cleanliness of the hydraulic station, is there any relevant rule requirement?Naturally connect the motor to the lift. When connecting, it must be ensured that the concentricity of the output shaft of the elevator is consistent with that of the input shaft of the motor, and that the outer flanges of the two are parallel. If the concentricity is inconsistent, it will cause the motor shaft to break or the elevator gear to wear.What kind of function can be achieved by installing the elevator? Before installation, confirm whether the motor and the elevator are intact, and strictly check whether the dimensions of the parts connected to the motor and the elevator match. Here are the dimensions of the positioning boss of the motor the input shaft and the groove of the elevator. Fitting tolerances.