ShijiazhuangDual track hydraulic lifting platformManufacturing analysis

If the elevator fails, non -electrical professionals must not disassemble and assemble electrical appliances at will to prevent mistakes or electric shock!Each institutional brakes should regularly check and adjust the gap between brake tiles and brake wheels to ensure flexibility and reliability. There should be no dirt on the friction surface. If there is dirt, it must be cleaned with gasoline or rare materials.Shijiazhuang,The lifting platform is different depending on the demand in the market, and it is also called. With the changes in market demand, the market has also appeared on the aluminum alloy lifting platform and aluminum alloy lift.Limerick,The middle turning shaft of the hydraulic lifting platform is inconsistent, resulting in the failure of the lifting platform to work properly. The platform was severely damaged. The table tilt appeared. Please check carefully before the factory did not do a strict tilt test before leaving the factory. It has caused a lot of accidents. For tilting testing, whether it is a fork -cut lifting platform or a rail -type lifting cargo ladder, it is from the power unit and the oil cylinder. The power unit has four holes during production. In the hydraulic oil flow, we can adjust the motor speed or electric hydraulic ratio valve to adjust the hydraulic oil flow; which factors will affect the lift speed oil pipe of the hydraulic lift. The longer the hydraulic oil pipe, the longer the upsurge. Therefore, during installation, the length of the oil pipe should be reduced as much as possible within the allowable range of the design; on the basis of adjusting the power unit, the size of the oil pipe can also be adjusted. On the premise of ensuring that the equipment meets normal demand, correspondingly can perform correspondingly Adjustment.The overall structure is intact to check whether the overall structure is deformed, and the important components are damaged, especially the load -bearing branches and chains.

The loading and unloading mobile boarding bridge is already a very easy -to -see structural form at the modern logistics site. It is the point and end point of the corporate logistics chain, and it is a installation and unloading operation platform for enterprises to quickly, turn on products and goods. The height of the loading and unloading operation platform is fixed, but there is always a height gap or gap between the height of the transportation of the carriage and the loading and unloading station. As a result, the transportation forklift cannot enter and exit and transport vehicles directly to load and unload the goods. Use Dengqiao Bridge to provide reliable connections. Make a forklift, and quickly enter and exit the transportation vehicle for loading and unloading operations.Everyone knows that the construction elevator will be used during the construction process. This is because the construction lift is stable and strong in use. At the same time, due to its small advantages,For project projects, if the purchased construction lift can ensure the safety of the life, of course, it can also improve the work efficiency of the entire construction. Therefore, there are many manufacturers of construction lifts on the market, when buying a lifting machine, we must first pay attention to its quality, many customers now have high requirements for crafts when choosing a lifting machine.Of course, it also needs to see its production. If a manufacturer has a large production, it shows that its strength is strong, especially the requirements for the production process of the construction lift is relatively high. When purchasing, it depends on the factory of his production, craftsmanship,ShijiazhuangHydraulic lifting platform manufacturer, etc. These are all important.Put all the hydraulic oil in the fuel tank, open the fuel tank, remove the oil absorbing filter, and put it back to the fuel tank, and install it in situ. The new oil is filled with new oil in the fuel tank.

The motor should be parked immediately when the motor is overheated. After the failure, the motor continues to run, and the motor bearing is good.Project scope,ShijiazhuangLifting hydraulic lifting platform,The current fixed hydraulic lift is mainly a closed or mesh lifting channel surrounded by buildings and light steel structures.The enclosed or mesh frame the fixed hydraulic lifting platform is installed on both sides of the fixed hydraulic lifting platform: it has a hydraulic driver motor, oil pump, safety valve, fixed hydraulic lifting platform speed regulating valve, exchanging direction valve and other hydraulic pressure The small fuel tank cylinder part of the component: consisting of one or more cylinder composition of one or more cylinder composition of the lift cylinder straight platform or a rising piercing pier. Doors, generally open platforms do not have door electrical parts: consisting of platform parts of power, signal, security, lighting and other devices: the steel structure platform that carries heavy objects, with closed (ie car) or open type, on both sides, sides, sides, sides, sides, sides, sides sides, sides, sides, and both sides. There are guided roller or guide boots, and the auxiliary part of a lifting cylinder or lifting fork -type steel frame can be connected at the bottom of the platform: it is composed of hydraulic pipes, pipes, pressure gauges, and steel structure bases; safety device: safety valve, limit limit, door door door, door, door, door, door door, door, door, door, door, door, door, door, door, door, door, door, door, door, door, door, door, door door, door door Electromechanical locks, rupture valves, emergency switch and short -circuit protection.Because the hydraulic lifting platform power unit requires oil sources, the structure is relatively complicated, and it also has certain pollution and influence on the environment. The movement device is relatively fast. The structure of the electric rod is very simple, and the space occupies is small, but there is no advantage in price, so the power supply will be used as the power source of the lifting machine. The DC motor is directly transmitted to other mechanical devices through the reduction of the reducer.Shijiazhuang,Because the hydraulic lifting platform power unit requires oil sources, the structure is relatively complicated and it also has certain pollution and influence on the environment. The movement device is relatively fast. The structure of the electric rod is very simple, and the space occupies is small, but there is no advantage in price, so the power supply will be used as the power source of the lifting machine. The DC motor is directly transmitted to other mechanical devices through the reduction of the reducer.The power unit is adjusted, whether it is a fork -cut lifting platform or a rail -type lifting cargo ladder, it is from the power unit and the oil cylinder. The power unit has four holes during production. In the hydraulic oil flow, we can adjust the motor speed or electric hydraulic ratio valve to adjust the hydraulic oil flow; which factors will affect the lift speed oil pipe of the hydraulic lift. The longer the hydraulic oil pipe, the longer the upsurge. Therefore, during installation, the length of the oil pipe should be reduced as much as possible within the allowable range of the design; on the basis of adjusting the power unit, the size of the oil pipe can also be adjusted. On the premise of ensuring that the equipment meets normal demand, correspondingly can perform correspondingly Adjustment.For the introduction of the daily maintenance of the lifting cargo ladder, the brakes of each organization should usually implement the interval between inspection and adjustment of braking tiles and brake wheels, and the management is sensitive and reliable. On the surface, there should be no dirt, and it must be washed off with gasoline or scarcity when encountering dirt.