Danube new townSelf hydraulic lifting platformThe molding process is different

When using hydraulic elevators, the main causes of noise are mechanical mechanism failures, hydraulic system failures, electrical equipment or component failures, etc. Today, the manufacturer of hydraulic cargo elevators will introduce to you the reasons for the noise generated by hydraulic elevators.The classification of lifting platforms is as follows: they are divided into mobile lifting platforms, automatic lifting platforms, hydraulic lifting platforms folding arm lifting platforms, and sleeve type lifting platforms according to their different modes of movement.Danube new town,Compare the measurement curves and then go to the variable displacement pump or variable speed motor. Long term targeting all types of high-priced elevator manufacturers nationwide with reasonable prices and comprehensive services we have gained recognition from our customersThe smoothness of the gearbox, external meshing gears, and hydraulic oil are all carried out according to the requirements in the smoothness table.Bissora,Pre install equipment, maintain unobstructed access roads and sufficient parking space before pre installation. Some hydraulic cargo elevators require heavy lifting assistance for installation, some require equipment such as forklifts for installation, and some can be pre installed manually. When it is necessary to install with the assistance of a truck crane and a forklift, full consideration should be given to whether the on-site environment meets the working conditions of the truck crane.Stable and widely applicable cargo lifting equipment is mainly used for transporting goods between height differences in production lines; Material online and offline; Adjust the height of the workpiece during assembly; High altitude feeder feeding; Lifting of components during assembly of large equipment; Large machine material and cutting; The warehouse loading and unloading site is equipped with forklift and other transportation vehicles for rapid loading and unloading of goods.The hydraulic lifting platform is a manually movable type, and the lifting power of the platform is a two machine or three-phase power supply. It has manual and electric power, and is also equipped with a hand pump for use in case of power outage. This series of platforms have the characteristics of flexible movement, stable lifting, and easy operation, and are mainly used in factories, government agencies, commercial stores, and the construction and decoration industry.

The installation personnel should have the qualification for installing hydraulic cargo elevators, carefully implement the special construction plan for installation and construction, and provide safety technical disclosure to the installation personnel for technical design.It must be abnormal. To solve the problem, the first step is to identify the cause of the problem. Professional elevator manufacturers have strict testing, quality assurance, and promotional activities are underway. Welcome to consultThe characteristics of the platform include reliable hydraulic system, simple operation, large load-bearing capacity, the greater the shaking. When using it at a working height of meters Road noise can also occur if tires are crushed against objects that are prone to noise. The shaking amplitude of the scissor type lifting platform is proportional to its lifting height. The higher the height,Danube new townMast type aluminum alloy hydraulic lifting platform, if possible, please use safety protection measuresCheck valve leakage: If the natural wear of the check valve exceeds the specified value after long-term use,Danube new townMobile elevator hydraulic lifting platform, it will cause leakage. Disassemble and clean the check valve, and replace it if necessary.When the hydraulic oil of the equipment is insufficient, it will not cause lifting. At this point, you only need to add enough hydraulic oil to run.

Therefore, the wholesale manufacturers of hydraulic elevators remind that there are three main ways to adjust the speed control circuit: throttling speed control circuit: quantitative pump oil supply, using flow valves to adjust the flow in and out of the actuator to achieve speed control; In the volume throttling speed control circuit, the oil is supplied by the pressure limiting variable pump, and the flow rate into the actuator is adjusted by the flow valve to adapt the flow rate of the variable pump to the regulated flow rate of the speed control valve.resources, the spring of the overflow valve is fatigued and deformed, resulting in unstable pressure regulation of the overflow valve, and the relief time of the overflow valve is too short, it is easy to cause the pilot valve performance of the overflow valve to be partially stable, causing air to vibrate inside the pilot valve and generate noise. So we need to regularly clean the overflow valve. When the overflow valve is damaged or severely worn, it should be replaced.Generally speaking, for situations with large lifting loads and small lifting heights, a lifting mechanism should be selected. For situations with small loads but large lifting heights, a lifting mechanism should be selected. According to the initial structure of the jacking, in order to meet the stability requirements, the size and lifting type of the oil cylinder are increased, and in order to achieve the same effective area as the jacking force, the oil cylinder is added. If the latter is larger, a lifting mechanism should be selected.After the pre installation is completed, the pre installed equipment should be fixed and the positions of cables,Danube new townHydraulic lifting platform, oil pipes, and components such as the pre installed frame should be confirmed to be correct before reinforcement work can be carried out. Reinforcement requires welding or screws, and the hydraulic cargo elevator after reinforcement has robustness and safety.Danube new town,Stability: The workbench should evenly withstand % of the MAX load capacity and be stable at the MAX elevation.The precautions to consider when selecting a hydraulic lift oil tank include: considering the structure of the oil tank, the partition in the traditional oil tank cannot settle dirt. A vertical partition should be installed along the longitudinal axis of the oil tank, with a space left between one end of the partition and the end plate of the oil tank to connect the gaps on both sides of the partition. The inlet and outlet of the hydraulic pump are arranged on both sides of the partition at the disconnected end, so that the distance Z between the inlet and return oil is far, The hydraulic oil tank has more heat dissipation effect.The classification of lifting platforms is as follows: they are divided into mobile lifting platforms, automatic lifting platforms, hydraulic lifting platforms, folding arm lifting platforms, and sleeve type lifting platforms according to their different modes of movement.