ReinaHorizontal slurry pumpWhat if something goes wrong

　　 If the power cord is not well contacted, it will also lead to the burning of the motor.　　During adjustment, firstly loosen the support cover, then compress the nut, and then loosen the bearing seat. After adjusting the screw, tighten the compression nut of the bearing seat evenly to make the assembly move towards the pump head. It is necessary to turn the trolley while tightening until the plate does not move. Rotate according to the pump operationReina,ReinaHorizontal slurry pump,　　Check the three-phase current with an ammeter on the control panel. If the phase power supply is found to be insufficient the power supply of the submersible pump shall be turned off immediately. Check whether the cable connector, connection point and power switch contact are in poor contact and whether they are the main line. Check whether the circuit wiring is broken or loose, or whether the fuse is damaged or burnt out　　 The rotor assembly is designed according to the actual situation, including the packing gland, packing ring and packing,ReinaSubmersible non clogging sewage pump, needs to be disassembled; Submersible slurry pump Disassemble the o-seal ring, shaft sleeve, balance disc and key on the shaft in turn, and then the discharge section includes the last stage guide vane　　The submersible slurry pump may be blocked when it is used at ordinary times. In particular, some equipment is frequently used at ordinary times, but the maintenance work is not done well when it is used, so it will be blocked after being used for a period of time

　　Be sure to choose a pump that is more suitable for use.　　For example, /c-ah slurry pump is a small-diameter slurry pump without impeller removal ring. When it is necessary to remove the impeller, we only need to fix the pump shaft, rotate the impeller in the opposite direction according to the rotation direction on the pump body, and then the impeller can be easily removed　　 If the head of the submersible slurry pump is too low or the head is higher than the practical condition, the flow will be large and the current will rise. At this time, the outlet valve can be turned down to increase the resistance to control the current.Welcome to inquire,　　 the water pipe shall be short, and the cavitation allowance of the device shall be greater than that of the pump. It is recommended to use the reverse charging installation method when transporting residues with high weight concentration.　　Submersible pump is a common water lifting equipment for deep wells. During operation, the whole machine intrudes into the water to extract water from the underground to the surface. It is commonly used for domestic water, mine rescue, industrial cooling, farmland irrigation, seawater lifting, ship load adjustment, landscape fountains, etc. Submersible pump is generally divided into clean water submersible　　If the shaft seal is not properly selected, it will not only require frequent maintenance during operation, but also leak a large amount of transmitted liquid.

　　Water pump is a kind of machinery that pumps energy liquid. It is a machine that converts the mechanical energy of the prime mover into the potential energy of the pumped liquid. Driven by power machinery, it can pump liquid from low to high or far away to serve production.technical service,ReinaCirculating hot water pipeline pump,　　Now you know the reason why the pump has air turbidity. In fact, this is a very common phenomenon. You don&#;t have to worry about it. Water pump can transport many things, such as water, oil, liquid metal, acid-base night and so on. It is a good means of transport.　　The self-priming pump is a self-priming centrifugal pump. It has the advantages of compact structure convenient operation, easy maintenance stable operation, long service life, and strong self-priming capacity. There is no need to install the bottom valve in the pipeline. Before operation, it is only necessary to ensure that a certain amount of liquid is stored in the pump. Different liquids can　　The first stage impeller of the pump is disassembled; It is also necessary to screw down the connecting nut between the water absorption section and the bearing body and the bolt on the bearing pressure connection, so that it is convenient for us to disassemble the bearing parts; When the shaft is pulled out from the suction section, the fixing nut on the shaft shall beReina,　　When the equipment is in use, the water delivered in the pump receives the friction with the surface of the pump impeller, so the pump needs to consume more energy to reduce the friction and resistance caused by the surface when it is rotating. Water will slowly overcome it as it flows　　Water pump is a kind of machinery that pumps energy liquid. It is a machine that converts the mechanical energy of the prime mover into the potential energy of the pumped liquid. Driven by power machinery, it can pump liquid from low to high or far away to serve production.　　Reasonable.