LegnanoPrice of guide rail type lifting platformWhat are the characteristics of the production line at least

Regarding the construction elevator with counterweight, check the adjustment and fixation status of the counterweight guide wheel. Check the balancing equipment of the steel wire rope, the crown wheel, and the counterweight steel wire rope bracketWhen disassembling the hydraulic oil tank filler cap, filter cover, inspection hole, hydraulic oil pipe and other parts, it is necessary to avoid dust during the system oil passage. The disassembled parts must be thoroughly cleaned before opening. When disassembling the hydraulic oil tank filler cap, first remove the soil around the tank cap. After loosening the tank cap, remove any remaining debris from the joint area (do not rinse with water to prevent water from seeping into the tank). Only after confirming cleanliness can the tank cap be opened. When using materials and hammers, materials that do not remove fiber impurities and specialized hammers with rubber attached to the surface should be selected. Hydraulic components and hydraulic hoses should be carefully cleaned, dried with high-pressure air, and then assembled. Choose a well packaged filter element (the inner packaging is damaged, although the filter element is intact, it may also be unclean). When changing the oil, clean the filter at the same time. Before installing the filter element, carefully clean the bottom dirt inside the filter housing with materials.Legnano, The lifting platform adopts a fully hydraulic lifting mechanism, which can be operated inside the platform bucket and on the elevator body. The working arm of the lifting platform can rotate degrees. The hydraulic system is equipped with a safety explosion-proof valve to prevent the main boom oil cylinder oil pipe from bursting. The hydraulic legs are equipped with a hydraulic locking device to prevent the leg oil cylinder from retracting. The hydraulic system is equipped with a platform overload automatic protection device, In order to ensure the safety of operators, each section of the working arm on platform is equipped with safety limit devices. The hydraulic system seals on platform are all well-known domestic and foreign brands, and the power of the entire vehicle is a diesel engine with its own power supply. The power supply can also be used. The hydraulic lifting platform is equipped with an emergency lowering device in case of power outage. The folding arm lifting platform product can also use a Hz, V power motor, and diesel engine dual power.Regarding the construction elevator with counterweight,LegnanoMobile cllimbing, check the adjustment and fixation status of the counterweight guide wheel. Check the balancing equipment of the steel wire rope, the crown wheel, and the counterweight steel wire rope bracketFloreshtAll connecting shafts must have split pins and be sufficient.Clean and inspect the crown wheel frame assembly, correct or replace with new partsCheck the interlocking equipment, up and down travel, and other safety maintenance switches of the cage door and fence door

The cleaning oil for the hydraulic system must use hydraulic oil of the same brand as the system used, with an oil temperature between and ℃. Use a large flow rate to remove impurities from the system as much as possible. The hydraulic system needs to be cleaned repeatedly three times or more. After each cleaning, fully drain the system while the oil is hot.The second method is the protective layer method, which covers the metal surface of the aluminum alloy lifting platform with a protective layer to isolate the metal products from the surrounding corrosive medium and prevent corrosion. Apply engine oil, hot plating or cover the surface of steel parts with corrosion-resistant non-metallic materials such as enamel and plastic; It is not easy to apply a layer of electroplating paint, spray plating, etc. on the surface of steelCheck the clearance of the ball bearing and the wear of the suspension wheel guide wheel. If the roller is worn, it is necessary to adjust or replace it. If the elevator bearing is worn, replace the guide wheel or bearingVariable cost,Leakage occurs due to looseness, vibration, and the influence of heat on the sealing surface and pipe joints of the machine; Some casting processing and other defects are difficult to detect during assembly and debugging, but due to vibration and impact during the operation process, these defects are exposed, manifested as oil (water) leakage. Therefore, leakage is prone to occur during the running-in period. Poor, due to the small fit clearance of newly assembled components and the difficulty in ensuring the uniformity of fit clearance due to assembly and other reasons, oil (grease) is not easy to form a uniform oil film on the friction surface to prevent wear. This reduces efficiency and causes early abnormal wear of the components. In severe cases, it can cause scratches or bite on the friction surface of precision fitting, leading to the occurrence of faults.Clean and inspect the crown wheel frame assembly, it is necessary to send it to a qualified professional unit for inspection and calibration. What are the functions of the lifting stage device?

Organize, and reinforce the severely corroded load-bearing membersClick to view,Transfer of goods between floors of rooms, restaurants, especially suitable for workplaces that cannot excavate pits. And there is no need for upper lifting points, double column, four column), stable equipment operation, simple and reliable operation, economic and convenient goods transmission, and difficult to solve narrow spaces that cannot reach the requirements. A customized delivery platform can be created, and the product hydraulic system is equipped with anti fall, upper and lower door interaction,LegnanoAluminum alloy lifting platform, and operation buttons can be set on each floor and lifting platform workbench to achieve multi-point. The product has a sturdy structure, a large load-bearing capacity, smooth lifting, simple and convenient installation and maintenance, making it an ideal and economical cargo conveying equipment for replacing elevators between low floors. The lifting stage device is mainly responsible for data processing of the operation mechanism and work bar of the vehicle, calculating the safety area of the lifting stage, and is suitable for the electric control system of the self lifting stage lifting platform. The main sensors in the electric control system include angle sensors, long angle sensors, dual axis inclination sensors, and energy saving of the oil cylinder system.The driver shall close and lock the movable doors at both ends of the protective fence before work, and then ring the bell to start. It is strictly prohibited to work with the movable doors of the protective fence open. In case of special circumstances during platform operation, the emergency stop switch can be used to stop the platform. However, during normal operation, it is prohibited to use the emergency stop switch to stop the platform.Regularly check all wires and cables for damage. Timely bandage and replace damaged parts.Legnano,LegnanoVertical obstacle free lifting platform,With the continuous development of the economy, meeting the needs of society, and increasing productivity, hydraulic cargo elevators play an important role in high-altitude operations. Hydraulic cargo elevators operate up and down, fully drain the system while the oil is hot.The lifting stage can provide real-time information on the operation of the entire vehicle with an oil temperature between and ℃. Use a large flow rate to remove impurities from the system as much as possible. The hydraulic system needs to be cleaned repeatedly three times or more. After each cleaning, avoiding relying solely on the experience of operators to coordinate with each other, and improving the reliability and safety of the system. The definition of safety zone is very important because the lifting stage has a large range of movements, and it must be accurately calculated. The lifting stage has two structurally separate systems, the ground turntable and the high-altitude work bar. However, for various movements on the vehicle, it is also an interconnected system, which needs to consider the priority of operation, system redundancy, and safety assurance of actions.