Fengzhen8-meter cargo elevatorClick to view

Regarding the cleanliness of the hydraulic station, is there any relevant rule requirement?Frequently check the humidity of the aerial work vehicle that is prone to water accumulation. It is inevitable that the aerial work vehicle is driving in rainy and snowy weather, or on muddy roads. The bottom and some gaps and indoor floors are easy to accumulate sludge. If the owner does not clean it in time,FengzhenBody guide rail type cargo elevator, this will hide the moisture. Therefore, the outer edge of the wheel hub, the door, the corner of the bottom of the trunk, the key hole and the wiper frame and other areas should be checked regularly, and the drainage holes in the door and various parts should be kept unblocked to ensure that the car seat covers, carpets and floors are protected from humidity. Rusty fittings.Fengzhen,Safety protection when using a mobile lift for high-altitude operations How to use the seat belt correctly: When using the belt, the belt must be tightened, and the waist buckle attachment must be tightened; The seat belt rope must be hooked on the ring of the seat belt rope; it is strictly forbidden to hang the seat belt on unstable or sharp-edged components; it is strictly forbidden to replace the parts on the seat belt; the shape is obviously deformed, or Seat belts that have previously been subjected to a severe impact are strictly prohibited.Prepare the foundation according to the foundation plan, pay attention to the alignment, leveling, and alignment to ensure the level of the foundation and various requirements for use.Kozani,Brake operators of various mechanisms on the equipment should regularly check and adjust the gap between the brake shoe and the brake wheel to ensure flexibility and reliability. Long-term promotion of freight elevator factory old brand, price advantage, quality guaranteed!Always check the connections of the various parts of the hydraulic lift, and tighten them if they are loose. The tightness of the connecting bolts of the body should be checked when the body is under pressure.Low cost: The cost is much lower than that of the scissor-type mobile lifting platform, so when purchasing a lifting platform, you must consider the scope of use of the lifting platform, the frequency of work, it should be fully considered whether the site environment meets the operating conditions of the steam crane.The open base of the adjustment plate makes it easier to clean up debris.The cleanliness of the hydraulic station is an important aspect of the elevator hydraulic station, so it should not be careless. Moreover, there are relevant rules and requirements, and you should refer to the specification manual,The daily maintenance of the hydraulic lifting platform in normal use is essential, but even if there is normal maintenance on the equipment, any possible problem cannot be ignored, so in order to ensure that the process of using the hydraulic lifting platform for each operation What aspects do we need to check before operation? Today, the editor will give you a popular science.Check the limit switch to see if all the limit switches are loose. If so,FengzhenProfessional guide rail type cargo elevator, please tighten them. Pay special attention to the ultra-high protection stroke of the hydraulic lifting platform to avoid accidents caused by the equipment exceeding the high safety height; check the pins (ear pins and center pins) Check whether the nuts, nuts, screws, etc. are loose, if any, and the pressure of the brushes should be adjusted so that the area is not less than %. Professional elevator factory, large quantity favorably high quality and low price. Fire-resistant-waterproof-high temperature resistant, durable, safe and reliable.

Safety performance: The lifting structure is made of high-strength manganese steel rectangular tube, and the scissor-type mechanical mechanism is easy to maintain, with strong stability and high carrying capacity. The maximum lifting height is about meters, and the maximum load is about tons. .plan,Naturally connect the motor to the lift. When connecting, it must be ensured that the concentricity of the output shaft of the elevator is consistent with that of the input shaft of the motor, and that the outer flanges of the two are parallel. If the concentricity is inconsistent, it will cause the motor shaft to break or the elevator gear to wear.Simple,FengzhenOne ton cargo elevator, in fact, some details should be paid attention to, as follows: It is actually difficult to insert them into the shaft pins when over-installing the bearings, but sometimes, in fact using a hammer to directly hit the bearing will cause great damage to the bearing, which is the main reason for bearing damage and reducing the service life of the bearing. Therefore, we must not overdo it when installing the bearing. It is best to put some soft cloth or cardboard on it before installing.As for the guide rail elevator installed outdoors, it is often exposed to rain and sunlight, so special attention should be paid to regular maintenance and inspection to avoid accidents.Fengzhen,The cleanliness of the hydraulic station is an important aspect of the elevator hydraulic station, so it should not be careless. Moreover, from a professional point of view, there are relevant rules and requirements, and you should refer to the specification manual, so that you can have a correct understanding and know how to achieve better cleanliness.The motor connection is wrong. When the delta connection motor is wrongly connected into a star shape, the motor still runs with full load, and the current flowing through the stator winding will exceed the rated current, and even cause the motor to stop by itself. If it overheats, it will burn out. When the star-connected motor is wrongly connected into a triangle, or the motor with several coil groups connected in series to form a branch circuit is connected in parallel with two branches, it will cause the winding and core to overheat, and in severe cases, the winding will be burned.The motor winding is short-circuited. When a short-circuit fault occurs in the motor winding the short-circuit current is much larger than the normal operating current, which increases the copper loss of the winding, causing the winding to overheat and even burn out.