ZhuangheMobile hydraulic turnover machineIndustry development opportunities and directions

Attention: The elevator consists of two main parts: mechanical and electrical. If the elevator is not maintained on a daily basis, it will cause wear and tear on the mechanical components of the elevator, greatly shortening its service life and preventing normal use of the elevator.Multiple elevator shafts can be connected and an - # I-beam can be fixed at a certain height between each adjacent elevator shaft, with the same position as the ring beam. The pit must be equipped with an isolation net that is mm above the ground level.Zhuanghe,When accidentally trapped in an elevator,ZhuangheFlip plate hydraulic roadblock machine, one should remain calm, press the alarm bell inside the elevator, and call the elevator emergency rescue phone or community property phone for help. Do not open doors or mess with buttons, and patiently wait for rescue.The speed limiter tensioning device and the steel belt tensioning device should be equipped with a safety switch.Nay Pyi Taw,Measurement of elevator and escalator shafts (III)To implement the arrangement of escalators and provide feedback, in order to determine the configuration of certain shared devices, the order of shipment,ZhuangheStage style lifting platform, and the alignment of handrail turns during continuous arrangement.The mechanical components of the elevator's traction machine require oil. There are two scales on the outer cover of the traction machine. Open the oil nozzle to check that the oil should be in the middle of the two scales. If the oil is lower than the lower scale, it means that the traction machine should be refueled. If not refueled, the elevator will not operate well for a long time, leading to the burning of the elevator traction machine and motor. After the elevator has been running for a long time, the oil should be replaced in a timely manner to keep the traction machine clean and in good condition.

If the elevator is in a downward direction, immediately close the door and return to the first floor station, and automatically open the elevator door.The elevator stops on the first floor and the door does not move: the fire emergency landing function of the elevator is triggered by smoke or thermal sensors inside the building.The mechanical components of the elevator's traction machine require oil. There are two scales on the outer cover of the traction machine. Open the oil nozzle to check that the oil should be in the middle of the two scales. If the oil is lower than the lower scale it means that the traction machine should be refueled. If not refueled, leading to the burning of the elevator traction machine and motor. After the elevator has been running for a long time the elevator will not operate well for a long time, the oil should be replaced in a timely manner to keep the traction machine clean and in good condition.Latest quotation,Measure the length, width, and depth of the pit (if any), and observe whether there are grooves and embedded parts at the support beam.The basic content of escalator shaft measurement is to measure the lifting height. The same as measuring the height of a straight ladder, strictly speaking, attention should be paid to whether there is a drop between the positioning point of the line drop and the decoration surface of the lower support beam of the ladder.The front room of the fire elevator is equipped with indoor fire hydrants.

The call button on each floor is no longer working,In the event of a fire when instructed by the fire center or the dedicated operation button of the first floor firefighter to enter the firefighting state, the elevator should immediately stop on the floor without opening the door, return to the first floor station, and automatically open the elevator door if it is in the upward direction.When accidentally trapped in an elevator, one should remain calm, press the alarm bell inside the elevator, and call the elevator emergency rescue phone or community property phone for help. Do not open doors or mess with buttons, and patiently wait for rescue.There is a dedicated fire telephone in the fire elevator car.Zhuanghe,Brick concrete structure elevator shaft: For unfinished brick structure shafts, users can be required to make a circle of beams at a certain height, arranged on three sides,ZhuangheStage hydraulic lifting platform, and disconnected on one side of the elevator entrance. The distance between the center heights of the beams depends on the product model, and should not exceed mm. The beam height should be mm, and the thickness should be the same as the wall. The lower ring beam is -mm away from the bottom of the pit, and the higher ring beam is -mm away from the lower surface of the shaft roof. The completed framework with a solid brick structure shaft can be equipped with steel plywood at the position of the fixed guide rail support frame. The position and size of the plywood are provided by the elevator, and the user is responsible for providing materials and construction. If the shaft structure is made of hollow bricks without ring beams, steel beams can be considered to be added between the frames for rectification.Please note that there should be a space of over mm left on both sides of the escalator, and when arranged in parallel, there is no restriction between the two escalators.The call button on each floor is no longer working, and the call is cut off.