DijonStainless steel heat exchange tubeThe structure and problems in the use process

Model & mdash; After that, the second widely used steel is mainly used in food industry and surgical equipment. Molybdenum is added to obtain a special corrosion-resistant structure. Because it has better chloride corrosion resistance than it, it is also made & ldquo; Marine Steel & rdquo; To use. SS is usually used in nuclear fuel recovery units. Grade stainless steel generally meets this application grade.Rockwell hardness the Rockwell hardness test of stainless steel pipe is the same as Brinell hardness test. The difference is that it measures the depth of indentation. Rockwell hardness test is widely used at present, which makes up for the disadvantage of Brinell method, It is simpler than Brinell method and can read the hardness value directly from the dial of the hardness machine. However, due to its small indentation, the hardness value is not as accurate as Brinell method.Dijon,Check whether the sealing ring of pipe fittings is complete and clean and whether the placement position is correct. If there is dirt, it must be cleaned up. If the sealing ring is damaged, it must be replaced again.Application field: launch the market plan of stainless steel pipe in the target market of new products, such as stainless steel kitchen equipment.Zalgoon shaher,When installing and welding the fixed port of stainless steel pipe, it is difficult to vent on the inner side, and some sides are easy to be blocked. In this case, water-soluble paper + blocking plate can be used for blocking. That is,DijonPerforated stainless steel disc, the easy to vent and good side can be blocked with blocking plate, the difficult to vent and bad blocking plate side can be blocked with water-soluble paper, and the weld on the outer side can be blocked with adhesive tape (see Table ) .When using this process, the following key points should be paid attention to: during the welding process the correct included angle between the welding handle, welding wire and weldment should be maintained. The ideal caster angle of the welding handle nozzle is & deg; & mdash; & deg;, and the included angle between the welding wire and the weldment surface is & deg; & mdash; & deg;; correct the molten pool temperature, change the included angle between the welding handle and weldment, change the welding speed, etc. to change the molten pool temperature, so as to ensure Beautiful weld formation (uniform width, no concave, convex and other defects) During operation, the current shall be slightly larger than that of solid core welding wire, and the welding handle shall be slightly adjusted to accelerate the separation of molten iron and molten flux coating, so as to facilitate the observation of molten pool and penetration; when filling the welding wire, the welding wire shall be regularly sent and taken out, and the welding wire shall always be ensured Under the protection of argon to prevent the end of the welding wire from being oxidized and affect the welding quality; pay attention to the welding quality of the arc and arc stop, and the spot weld shall be polished to & deg; the slope shall be gentle, and pay attention to the defects such as arc pit and shrinkage hole during arc stop.The experimental ice load of concrete decorated stainless steel pipe is the highest in the cold area

Application fields: chemical industry, construction industry.Stainless steel pipe is a long strip of steel with hollow section and no joints around it. The thicker the wall thickness of the product, the more economical and practical it is. The thinner the wall thickness, the higher its processing cost will be.In many construction sites, we use this kind of welding for priming, which can effectively ensure its quality and has certain construction difficulties. Therefore, careful and skilled welders should be selected for this work.Quality assurance,Ferritic stainless steel the Cr content of ferritic stainless steel is generally % ~ %, and the carbon content is less than .%. Other alloying elements are sometimes added. The metallographic structure is mainly ferrite, and there is no & alpha during heating and cooling=& amp; amp; gt;& gamma; The transformation cannot be strengthened by heat treatment. Strong oxidation resistance. At the same time, it also has good hot workability and certain cold workability. Ferritic stainless steel is mainly used to make components with high corrosion resistance and low strength requirements. It is widely used in manufacturing equipment such as production,DijonStainless steel hexagonal tube, nitrogen fertilizer and chemical pipelines.Refining and transportation industries are in great demand. Secondly, geological drilling, chemical industry construction industry, machinery industry, boiler, medical equipment furniture and bicycle manufacturing also need a large number of various steel pipes. With the development of new technologies such as atomic energy, rocket, missile and aerospace industry, stainless steel pipe plays an increasingly important role in national defense industry,DijonStainless steel plate air duct, science and technology and economic construction. the responsibility of the calender is that the annealed steel strip is blackened, the furnace liner is perforated, and ammonia leakage will cause rust. . The responsibility of the steel plant is that the peeling and trachoma of the steel strip will cause rust. Substandard materials will cause rust. the responsibility of the calender is that the annealed steel strip is blackened, the furnace liner is perforated, and ammonia leakage will cause rust. . The responsibility of the pipe manufacturer: the welds in the pipe manufacturer are polished rough, which will cause rust.

Stainless steel pipes and water transmission equipment for fluid transportation such as water and gas are advanced basic water purification materials in the world. They have strong anti-corrosion performance, which can not be compared with cast iron pipes, carbon steel pipes and plastic pipes.Installation works,This material without titanium and niobium has an inherent tendency of intergranular corrosion. Intergranular corrosion can be reduced by adding titanium and niobium and stabilizing treatment. It is a kind of high alloy steel that can corrode in air or chemical corrosive medium. Stainless steel has beautiful surface and good corrosion resistance. It does not have to undergo surface treatment such as color plating to play a role of rust free　　— It has better temperature resistance.;- Ferromagnetism due to m transformation shall be considered in use (such as in instrument parts).Dijon,Crimping: during crimping, the convex part of the pipe fitting is placed in the concave groove of the die, and the jaw is perpendicular to the pipe axis.Rockwell hardness the Rockwell hardness test of stainless steel pipe is the same as Brinell hardness test. The difference is that it measures the depth of indentation. Rockwell hardness test is widely used at present, and HRC is second only to Brinell hardness Hb in steel pipe standards. Rockwell hardness can be used to measure metal materials from very soft to very hard, It is simpler than Brinell method and can read the hardness value directly from the dial of the hardness machine. However, due to its small indentation, the hardness value is not as accurate as Brinell method.CE--“ Code for design of cold formed stainless steel structural parts & rdquo; And & ldquo; jointly published by nidi and euro inox; Structural stainless steel design manual & rdquo; The design of structural parts for buildings with long service life and good integrity has been simplified.