TasbogotSewage pump divingSeveral accidents prone to occur

　　When the water level reaches, the frequency of the frequency converter drops, and the slurry pump operates at a low speed. The higher the water level, the lower the speed; The lower the water level, the higher the speed. At the same time, the water level signal is transmitted to the control cabinet so that the operators can timely understand the liquid level. Through this control, the circulation in the slag slurry pool is basically unchanged　　Where ρ—— Density of transmission medium liquid (kg/m; γ—— Gravity of medium liquid (n/m; H -- pump lift (m); Q - water pump flow (m/s); G - gravitational acceleration (m/s.　　The difference between the shaft power P and the effective power PE is the power loss in the pump, which is measured by the pump efficiency. The pump efficiency is the ratio of the effective power and the shaft power, which is measured by η Indicates.Tasbogot,　　The submersible sewage pump is a kind of pump product which is connected with the motor and works under the water at the same time. Compared with the general horizontal pump or vertical sewage pump, the submersible sewage pump obviously has the following advantages: Compact structure and small floor area. Submersible sewage pump is submerged　　Submersible slurry pumps are mainly used in mining, coal, environmental protection, in the field of chemical industry, corrosive mixed pastes of chemical crystals are transported. Electric ash removal, coal washing plant slurry transportation, etc. Submersible slurry pump bladeTarime,　　 We must choose to consider the actual use situation when making the selection, because there will be some difference between the marked head when using and the head when using. This is because the pipe itself　　At present, mechanical seals occupy an increasing share in the slurry pump seal market.　　The high-efficiency slurry pump has three characteristics: first, the slurry pump has high operation efficiency and low loss.

　　When the water pump is driven by electricity or diesel engine, the atmospheric pressure will move the water pressure to pump water. In fact thus forming a vacuum in the impeller. In this way,TasbogotVortex pump and pipeline pump, from a al point of view, it is to convert electrical or chemical energy into gravity　　The sheath is divided into front sheath and rear sheath, which are made of natural rubber. The lining is made of high chromium alloy, so it has good wear resistance. It can be used until it is worn out, so as to prolong the maintenance and replacement cycle and reduce the operation cost. The outlet of this series of pumps can be installed at angles　　Occurrence of personal injury accident. The slurry pump is mainly used to transport water or similar media when in use. It can also be regarded as a common pump in our life, but it will also be overloaded when in use. Let&#;s have a look todaysupply,　　 First remove the pump from the engine.　　Ensure that the service time will be extended when it is used. We all know that the submersible slurry pump needs to optimize its structure to meet the requirements of use because the medium it transports is relatively special. The structure has been optimized to　　Start the priming pump. Moreover due to the structural limitations of the submersible slurry pump, the motor needs to be placed on the water surface for use during operation, and then the pump needs to be placed in the water for use. Therefore, the submersible slurry pump must be

　　 install a valve to inject water at the water inlet and outlet. This method is to install a valve on the water inlet pipe of the submersible slurry pump and connect the water pipe to inject water into the pump. This is a common and simple method.retailer,　　Submersible slurry pumps generally need to use some composite materials for manufacturing when they are used, so that they can have good wear and corrosion resistance when they are used, and can be used to transport most of the media when they are used. Phreatic slurry　　Several common specifications and models.　　 if the removed gasket is seriously damaged,TasbogotVertical centrifugal slurry pump, a new gasket shall be replaced. The removed parts shall be cleaned with kerosene before assembly.Tasbogot,　　Be sure to choose a pump that is more suitable for use.　　 Protective packing of shaft seal the shaft seal pump shall regularly check the sealing water pressure and water volume keep a small amount of cleaning water flowing along the shaft,TasbogotHorizontal wear-resistant slurry pump, regularly adjust the packing gland, check the packing and regularly replace the packing. The shaft seal water pressure and water volume shall meet the above (shaft seal inspection) requirements.　　 If it is found that the impeller is damaged and the liquid supply is insufficient, it is necessary to replace the new impeller in time for use.