La benlantaHigh pressure alloy pipe 12Cr1MoVGJin Jiu is approaching, prices fluctuate upwards

The production process can be summarized as follows: pre leveling → finishing → straightening → post leveling. Flat steel / A / B steel with width of -, thickness of -, rectangular section and slightly pure edge. Flat steel can be finished steel, or it can be used as blank for welded pipe and thin slab for laminated thin plate.Application characteristics of I-beamLa benlanta,A major defect is its instability to the corrosion process which can not resist all factors. Producers need a solution that can solve the corrosion problem. The decision has been found. They become a galvanized steel pipe. H-section steel is an economic section steel with better mechanical properties than I-section steel. It is named because its section shape is the same as the English letter 'H'. The flange of hot rolled H-beam is wider than that of I-beam, with large lateral stiffness and strong bending resistance. Under the same specification, H-beam is lighter than I-beam.Ali SabiehWhen we carry out different projects, we must use different raw materials, which can ensure the quality of the project. In many kinds of data, alloy pipe is widely used. In many projects, we will apply it, so it is very popular in the field. When people carry out the construction of alloy pipe project, there are many things that must be paid special attention to. Let&#;s take you to know:The shape of I-beam is similar to that of H-beam. What is the difference between them?H-section steel is an economic section high-efficiency profile with more optimized section area distribution and more reasonable strength weight ratio. It is named because its section is the same as the English letter 'H'. There is no slope on the inner side of the two outer edges of H-section steel, which is straight. This makes the welding and splicing of H-section steel simpler than I-section steel, better mechanical properties per unit weight, and can save a lot of materials and construction time.

Pass designExternal steel bonding reinforcement method is a more traditional reinforcement method. The utility model uses an adhesive to paste the steel plate or reinforcement mesh on the cracked part of the wall to achieve the purpose of reinforcement. The commonly used adhesive is usually epoxy resin. This method is simple and fast in construction and has little impact on production and life. Basically, the moment of inertia of the two main shafts on the section is quite different, which limits its application range. I-beam shall be selected according to the requirements of design drawings. In the structural design, the use of I-beam should be reasonably selected according to the mechanical properties, chemical properties,La benlanta40Cr alloy pipe manufacturer, weldability and structural size of I-beam.productionThe flange of H-beam is of equal thickness, including rolling section and combined section composed of three plates welded. All I-beams are rolled sections. Due to poor production technology, the inner edge of the flange has a slope of : The rolling of H-beam is different from that of ordinary I-beam. Only one set of horizontal rolls is used. Because its flange is wide and has no inclination (or the inclination is very small), a group of vertical rolls must be added for rolling at the same time. Therefore, its rolling process and equipment are more complex than ordinary rolling mills. The maximum height of rolled H-section steel that can be produced in China is mm, which exceeds the welded composite section.Pass designBecause the section size of ordinary I-beam and light I-beam is relatively large and narrow, the moment of inertia of the two main shafts on the section is quite different,La benlantaWholesale of I-beam manufacturers, which limits its application range. I-beam shall be selected according to the requirements of design drawings. In the structural design, the use of I-beam should be reasonably selected according to the mechanical properties, chemical properties, weldability and structural size of I-beam.

The specification of I-beam is expressed in cm of waist width. For example, the waist width of No. I-beam is cm. The types of I-beam include hot-rolled ordinary I-beam Light I-beam and wide parallel leg I-beam (H-beam). The waist width of hot-rolled ordinary I-beam in China is ~ mm, expressed as No. ~ No., and the inclination of inner side wall of leg is : The pass system of rolled I-beam includes direct rolling pass system, cross rolling pass system and mixed pass system. In addition, I-beam can also adopt special rolling method.build,As shown in the name, generally :, which makes the outer flange thin and the inner flange thick. Therefore, the section characteristics of I-beam in the two main planes are very different, and it is difficult to give full play to the strength characteristics in application. Although the thickened I-beam has also appeared in the I-beam market, the structure of the I-beam has determined its torsional performance.Galvanized pipe is often seen in our daily life, especially in some construction sites. This product has the advantage of durability when used. It also has the characteristics of surface gloss, uniform zinc layer and no missing plating. Moreover, the cost of hot-dip galvanizing for rust prevention is lower than that of other paint coatings. In addition, this product also has the characteristics of no dripping, strong adhesion, breaking the clean Legion and strong corrosion resistance. Even if it is used in some places where the environment is not good, its service life is also very long, and it also has the characteristics of corrosion resistance. The standard anti rust thickness of hot-dip galvanizing can be maintained for more than years without repair. This is used in some suburban environments. However, in urban or offshore areas, standard urban or offshore areas can be maintained for years without repair. The products produced by our company must meet these requirements. Friends who need to order can call us directly.With the development of steel structure buildings, that is, thickened I-beam, which is easy to lose stability for load-bearing columns.La benlanta,Main uses: as a finished material, flat steel can be used to make hoop iron tools and mechanical parts, and used as building frame structural parts and escalators in buildings. Flat steel is divided into two types according to its shape: plane spring flat steel and single-sided double groove spring flat steel. Hot rolled spring flat steel is mainly used to manufacture leaf springs for automobiles, tractors, railway transportation and other machinery.The section of I-beam has good straight pressure and tensile resistance, H steel has its own advantages and disadvantages.Its heat sealing effect is remarkable. It can be directly buried immediately, which can not only save resources, but also reduce consumption, not occupy the natural environment, but also purify the environment. The transportation of gas can meet the requirements of long-distance transportation, prevent actual operation and maintenance, meet the requirements of thermal insulation and cold protection, reduce heating equipment, unique and convenient installation, and reduce the construction cycle time of the project. On the whole, it is more convenient to use. It can also be used for the transportation of floor heating and hot springs.