KingstonWQ submersible sewage pumpThe mode of communication should be adapted to local conditions

　　Some of them are OK. For irrigation and other purposes, in fact, we choose to use larger flow. Let&#;s take a look at the method of selecting pumps.　　The installation of submersible slurry pump is a step that needs to be concerned. Since we all care about it, it is mainly because the installation will directly affect the use effect. The installation work should be seamless. Some key operating points can be seen when installing the slurry pump.Kingston,　　And has a wide range of applications.　　The submersible slurry pump is a slurry pump which is connected with the motor and works under the water at the same time. Compared with horizontal slurry pump and vertical slurry pump the biggest advantage is that it is flexible,KingstonQuotation slurry pump, convenient and easy to apply to various working conditions. The most important technical point of submersible slurry pump is the tightness between its motor and pump body Stability and reliability of seals.Gambela,　　Submersible slurry pump is a kind of pump used in mines. Do you know the effect and form of its shaft seal? Let&#;s have a look.　　 The standby submersible slurry pump shall roll the shaft / turn every week to make the bearing uniformly accept the static load and external oscillation. The building structure in the water pump room shall be reconstructed. Sound absorbing and isolating plates shall be installed around the wall and on the top of the machine room and fixed with light steel keel; The connecting holes between the machine room and other rooms are tightly blocked,　　Therefore, the correct selection of shaft seal can ensure the safe and stable operation of slurry pump.

　　It is longer and saves production cost. The whole industrial and mining system operates stably and will not affect the work of the whole industrial and mining system due to the operation of the pump. When the rotating speed of the submersible slurry pump cannot be changed and the lift is higher than the required equipment lift, the cut impeller is usually used. The cut is　　If this coating is removed over time in subsequent work, the owner of the stainless steel deep well pump can use another coating to resist corrosion and hot water.　　It needs to be replaced in case of damage, swelling and deformation, insufficient spring pressure, breakage, etc.Customer first　　With the continuous development of slurry pump technology, submersible slurry pump has also responded to the market demand. At the same time this type of pump is especially suitable for the depth where the vertical slurry pump cannot operate. Pay attention when using the equipment. The submersible slurry pump can operate if its depth is less than m, but it exceeds　　If the oil seal ring of the shaft is seriously worn, replace it with a new one.　　Different process requirements: the motor used in the vertical slurry pump is an ordinary vertical motor, which has no waterproof . The motor of the submersible slurry pump and the pump shaft are coaxial. The motor shall be waterproof and sealed. The motor and the pump body can invade underwater at the same time.

　　The application of pumps involves all aspects of work and production, and the types of pumps are also diverse. Some of the same pump have several names, and some of the names are very similar, we will introduce the submersible pump and the submersible slurry pump. Is there any difference between the twoQuality improvement,　　Basically, the reasons for the motor heating of the submersible slurry pump are the above items. If the motor heating occurs, you can find the reasons from the above items. However, it must be noted that if the fault is caused by electricity, people who do not know electricity should not repair it by themselves, so as to avoid people　　When transporting grinding slurry containing solid particles, some small failures will inevitably occur after long-term use. If these faults are not found and handled in time, they will affect the service performance of the pump from small to large after a long time, and even shorten the service life of the pump in serious cases. To avoid　　After a certain value, which is called the vaporization pressure of water at this temperature.Kingston,　　 It may be that the motor power of the water pump is too large,KingstonFire deep well pump, the working current is too large, and the heat generation is too large,KingstonSubmersible sewage pump, resulting in the high temperature of the vacuum pump.　　 Then unscrew the nut at the front end of the pump shaft, remove the cover plate, and press out the middle impeller and water seal.　　 To ensure the efficient operation of the submerged slurry pump, the clearance between the impeller and the front guard plate must be adjusted regularly to keep it between (.-mm). In addition to monitoring the flow and pressure during the operation of the pump