St TrudenSubmersible non clogging sewage pumpReduce labor costs for part quality

　　During normal operation, the temperature of the motor is very high, some even as high as ℃. In this case, or　　 Structural features and working principle qsz submersible slurry pump is a coaxial integration of water pump and motor. During operation one motor burns out at this time. Don&#;t worry about replacing it. You must find out the cause of the motor&#;s heating, the motor shaft drives the water pump impeller to rotate, and transmits energy to the slurry medium to generate a certain flow rate, drive the solid flow, and realize the transportation of slurry.St Truden,　　From the working principle, Li is a centrifugal pump. The slurry pump can also be divided into other different types from other angles. Let&#;s see from what angle Panshi pump can classify the slurry pump: first, the suction inlet of the slurry pump　　 Precautions for disassembly of submersible slurry pump Before disassembling the filter press,St TrudenVertical non clogging sewage pump, make sure that the liquid in the submersible slurry pump is completely discharged. If the rotor is disassembled, drain the lubricating oil in the rotor bearing housing. If the newly added oil is stored, it should continue to be used after maintenance. Do not dump it directlyBayt Fajjar,St TrudenSplit vertical pipeline pump,　　Potential is convenient and flexible. It is easy to operate. It can be operated by a fool who turns on the power supply under immersion; It has a wide range of applications. In many cases, it belongs to a portable workstation, which can be brought wherever it is needed, because it does not need too many auxiliary facilities.　　It will burn out. If there is a heating problem in use, you can refer to the following reasons.　　 Selection of pipeline diameter: the selection of pipeline shall consider the one-time purchase cost, long-term operation cost and operation reliability.

　　 The fixing method of the impeller is changed from screw thread to key clamp to prevent the impeller from falling off and causing damage!　　Therefore, it can be directly installed in the sewage tank without building a special pump room to install pumps and machines,St TrudenSubmersible sewage pump, which can save a lot of land and infrastructure costs.　　It is occasionally found that there is insufficient liquid supply when using, so what are the reasons for this situation and how to deal with it.supply, we can check whether these reasons are the above. This is also a reminder that we need to maintain the pump during normal use. latent　　The hardened mud layer collapses after softening, avoiding the phenomenon of burying the pump during use.　　 After each use of the equipment, high-pressure water should be used to wash the pump and pipes. The washing can be stopped until the water has no impurities.

　　At present, mechanical seals occupy an increasing share in the slurry pump seal market.Installation conditions, the equipment will use centrifugal force to drive the liquid from the impeller to the outer edge and obtain energy, and then leave the edge of the impeller at a higher speed　　 Change the oil: if the oil contains water, drain it, change the oil seal the gasket, and then tighten the screw plug.　　The pump can often be selected according to the specific requirements of lift, flow and liquid delivery. The flow range of the delivered liquid is - L / s, the pressure range is .- MPa, and the diesel engine speed range is - rpm. Features: water pump, high automation and performanceSt Truden,　　In the application of pumps, the first thing we think of is water. Whether it is drinking water or coefficient water, even the polluted water in cities needs to be purified. All these require its equipment to provide services for us. Without pumps, our basic survival is a problem.　　Yes, summer is the peak sales season. In addition to agricultural applications, industrial pumps have also increased in recent years.　　Head refers to the energy obtained from the pump by the unit weight of liquid output by the pump, so head refers to the effective energy obtained from the liquid output by the pump in unit time - that is the effective power of the pump: the equation is PE= ρ GQH (W)= γ QH (W)