Colorado SpringsHydraulic lifting platform frameDesign features

The downward movement of the hydraulic cylinder (i.e. lowering of heavy objects). The hydraulic oil enters the upper end of the hydraulic cylinder through the explosion-proof electromagnetic directional valve, and the return oil from the lower end of the hydraulic cylinder returns to the oil tank through the balance valve, hydraulic control one-way valve, throttle valve and explosion-proof electromagnetic directional valve. To ensure a smooth descent of heavy objects and safe and reliable braking, a balance valve is installed on the return oil circuit to balance the circuit and maintain pressure, so that the descent speed does not change due to heavy objects. The throttle valve regulates the flow rate and the ascending and descending speed. To ensure safe and reliable braking and prevent accidents, a hydraulic control one-way valve, also known as a hydraulic lock, is added to ensure safe self-locking in the event of an accidental rupture of the hydraulic pipeline. An overload sound control alarm has been installed to distinguish between overload or equipment failure.The classification of lifting platforms is as follows: they are divided into mobile lifting platforms automatic lifting platforms,Colorado SpringsCustomization of hydraulic lifting platform, hydraulic lifting platforms folding arm lifting platforms, and sleeve type lifting platforms according to their different modes of movement.Colorado Springs,Based on experience, new steel wire ropes will not suddenly break when used under normal circumstances,Colorado SpringsElectric hydraulic lifting platform, unless incorrect operation or safety protection devices fail, as the load borne by the steel wire may exceed its breaking capacity. The damage to the steel wire rope of the cargo elevator is mainly gradually formed during long-term use. After a certain period of repeated bending and friction, the steel wire on the surface of the steel wire rope will experience bending fatigue and wear, and the steel wire on the surface layer will gradually break. At this point, if it cannot be used again, it should be replaced in a timely manner to ensure the safety of the hydraulic platform.The manufacturer of hydraulic cargo elevators will tell you about the knowledge of specialized lifting platforms for unloading.Richmond-Hill,The lifting platform is a multifunctional heavy loading and unloading mechanical equipment, which can be divided into fixed and mobile, guide rail and curved arm types. Fixed types include scissor elevators, chain elevators, loading and unloading platforms, and attached electric construction platforms.The manufacturer of the hydraulic cargo elevator tells you the reason and cleaning method: Reason: Overload cleaning method: Reduce the load to clean. Reason: The return valve is not closed. Cleaning method: Tighten the return valve to clean. Reason: The one-way valve of the manual pump is stuck and the return valve is malfunctioning. Cleaning method: Unscrew the bolt at the valve port of the oil pump, conduct maintenance, cleaning, and replace the cleaning hydraulic oil to clean.Check valve leakage: If the natural wear of the check valve exceeds the specified value after long-term use, it will cause leakage. Disassemble and clean the check valve, and replace it if necessary.

After hours of elevator operation, perform minor repairs to the mechanical and electrical systems.One of the executing components of the hydraulic cargo elevator system is the hydraulic cylinder. The hydraulic cylinder is responsible for linear lifting or retraction. Its characteristics are light weight, high power, simple structure, convenient maintenance, low motion inertia, frequent commutation, and convenient remote control. Hydraulic cylinders are widely used in various single acting hydraulic cylinders as an example to analyze the conversion of hydraulic energy into mechanical energy for linear motion.Therefore, in the hydraulic pipeline assembly line, it is necessary to avoid dead bends as much as possible and check the tightness of the sleeve in a timely manner.where,When the hydraulic oil of the equipment is insufficient, it will not cause lifting. At this point, you only need to add enough hydraulic oil to run.The development of elevators is at its peak, as many manufacturers have chosen more multi-story buildings to fully utilize the site, so they also need a device to facilitate the improvement of goods.Remove the hydraulic oil tank filler cap, filter cover, inspection hole, hydraulic oil pipe and other parts to avoid dust when removing the system oil pipe. Clean the disassembled parts before opening them. When disassembling the hydraulic oil tank filler cap, first remove the soil around the tank cap, loosen the tank cap, and remove any remaining debris from the joint (do not rinse with water to prevent water from seeping into the tank). After confirming cleaning,Colorado Springs10 meter lifting hydraulic platform, they should be placed in the middle of the platform as much as possible. The weight of the goods should be within the standard load range of the equipment, and the volume of the goods should not exceed the platform size of the equipment. Otherwise, materials and lifting platforms may be injured and dangerous accidents may occur. High priced and various specifications of elevator manufacturers provide timely supply, with high cost-effectiveness, and have become the preferred brand for many wire products. Welcome to purchase!plan,Before installation, leveling, and alignment points, and those who suffer from mental illness, epilepsy, or have been identified by a doctor as having hypertension heart disease, or other diseases that are not suitable for high-altitude operations are not allowed to participate in high-altitude operations. When it is found that staff members are drinking alcohol or feeling low spirits, it is prohibited to work at heights.The manufacturer of hydraulic cargo elevators will tell you about the knowledge of specialized lifting platforms for unloading.Colorado Springs,The electromagnetic coil of the electromagnetic directional valve is not firmly fixed, and frequent separation and suction can also produce high noise.Motor not running: Check all components of the motor for damage and check if there are any problems with the circuit and wiring.Solution: Check if the performance of the legs is good, even if the butter is polished to increase its properties.