Beverwick1 ton small lifting cargo elevatorGrowth trend

The boxes and distribution boxes of the hydraulic lift are always kept clean, it must be ensured that the concentricity of the output shaft of the elevator is consistent with that of the input shaft of the motor, and that the outer flanges of the two are parallel. If the concentricity is inconsistent, it will cause the motor shaft to break or the elevator gear to wear.Beverwick,The second is that steel will have obvious effects of thermal expansion and cold contraction at low temperatures. Although this property of steel will be taken into account when designing and manufacturing hydraulic lifts, after all the environment is different. Under low conditions, steel will appear. Some unstable performances, such as increased hardness, decreased toughness, etc. At this time, it is necessary to pay more attention to the maintenance of equipment to keep the key parts in order to avoid dry grinding.After the goods are transported, clean up the debris on the platform.Sanhe-City,Check the limit switch to see if all the limit switches are loose. If so please tighten them. Pay special attention to the ultra-high protection stroke of the hydraulic lifting platform to avoid accidents caused by the equipment exceeding the high safety height; check the pins (ear pins and center pins) Check whether the nuts, nuts, screws, etc. are loose,BeverwickGuide rail chain lifting cargo elevator, if any, should be reinforced immediately; ensure that the hydraulic lifting platform rises and falls smoothly; outriggers (for high-altitude operating platform)Many customers think that the operating power supply of the hydraulic lifting platform is below the safe voltage of V and there will be no electric shock. They are wrong. Normally, there will be no electric shock, but if there is improper operation, it will still be very dangerous. So how can we effectively prevent the occurrence of electric shock accidents? Today, the editor will share safety knowledge with you.Ensure good power supply at the installation site, install a separate distribution box, and the leakage switch must meet the requirements for construction elevators when used in the distribution box. If the construction elevator installed is frequency conversion, the leakage switch should be adapted to the frequency converter when selecting the leakage switch .

Are the water cooling and air cooling of the hydraulic station the same?Avoid, especially during storage. Store in a cool, dry place, and avoid rain and snow during work.Ensure good power supply at the installation site, and the leakage switch must meet the requirements for construction elevators when used in the distribution box. If the construction elevator installed is frequency conversion, the leakage switch should be adapted to the frequency converter when selecting the leakage switch .Good reputation,Unscrew the screw on the dust-proof hole outside the flange of the elevator, adjust the PCS system ring to align the side hole with the dust-proof hole, and tighten the inner hexagon. After that, remove the motor shaft key.What are the maintenance rules for hydraulic lift machinery? The brakes of each mechanism should be checked frequently and the gap between the brake shoe and the brake wheel should be adjusted to ensure flexibility and reliability. There should be no dirt on the friction surface, it must be washed off with gasoline or thinner.The parts such as reduction box, gearbox, external gear and hydraulic oil are all in accordance with the requirements in the table.

Check the limit switch to see if all the limit switches are loose. If so, please tighten them. Pay special attention to the ultra-high protection stroke of the hydraulic lifting platform to avoid accidents caused by the equipment exceeding the high safety height; check the pins (ear pins and center pins) Check whether the nuts, nuts, screws,BeverwickFixed hydraulic lifting cargo elevator, etc. are loose if any, should be reinforced immediately; ensure that the hydraulic lifting platform rises and falls smoothly; outriggers (for high-altitude operating platform)Promise and keep promise,The hydraulic lifting platform is mainly the pressure transmission of hydraulic oil to realize the lifting function. Its scissor mechanical structure makes the lift stable,BeverwickElevating cargo elevator, and the wide operating platform and high carrying capacity make the high-altitude operation wide and suitable for many people work at the same time. It makes high-altitude operations efficient and secure.It adopts a scissor-type mechanical structure, so that the aerial work platform can still move stably when it carries a large weight and rises to a large working height. It is its larger range of high-altitude operations and carrying capacity that make it widely used in various fields. The self-propelled scissor-type aerial work platform can walk quickly or slowly at various heights during operation, and can conveniently and continuously complete operations such as forward, backward, up and down, left and right steering on the operating platform. Make high-altitude operations more efficient and more secure. Therefore, it has received more widespread attention in the market.Prepare the foundation according to the foundation plan, pay attention to the alignment, leveling, and alignment to ensure the level of the foundation and various requirements for use.Beverwick,The design of the hydraulic lifting platform is unreasonable. When the designer designs the cylinder barrel and rod, if there is a problem with the design size and angle, then there will definitely be problems in the later stage. Therefore, it is necessary to confirm the technical strength of the manufacturer when working on a hydraulic lifting platform; what is the problem with the sound of the oil cylinder of the hydraulic lifting platform? Design drawings to make, the angle of the oil cylinder is slightly deviated, it will cause the friction between the cylinder barrel and the rod, which will cause the sound; the seal quality of the hydraulic lifting platform is different, and the use of different seals will also affect the sound of the oil cylinder, and the seal with excellent material The continuous friction between the parts and the cylinder wall will cause the sound to be very loud, and long-term wear and tear may scratch the oil cylinder and cause oil leakage, so when the hydraulic lifting platform is used, pay attention to ask the manufacturer what brand and material the seal is used; In some cases of mechanical running-in, it is not ruled out that the above three situations are normal, and there will still be noises. If there is no problem after investigation, then don’t worry. It’s just a running-in problem between mechanical parts. It will disappear naturally.The use of elevators is not to maintain and overhaul after the equipment fails. It is necessary to maintain the equipment according to the correct maintenance and overhaul