ShemonaFire deep well pumpproduction

　　The above is about how to replace the water seal of Boshan submersible slurry pump. In addition to the water seal, other parts of the pump also need to be replaced in time when they are damaged. Moreover, some parts of the pump are relatively easy to be damaged, and different pump models have different performance and application fields. Therefore, although the pump has a wide range of applications if its model is not correctly and reasonably selected, its application effect will be greatShemona,　　The liquid level of slurry shall be higher than the inlet of pump.　　Promote the continuous expansion of the sales network group.Ejigbo,　　Balance of.　　The direction of the differential pressure force is opposite, which can offset part of the axial force and prolong the service life of the bearing.　　Water pump is a kind of machinery that pumps energy liquid. It is a machine that converts the mechanical energy of the prime mover into the potential energy of the pumped liquid. Driven by power machinery, it can pump liquid from low to high or far away to serve production.

　　 for screws that are too tight or rusted for a long time,ShemonaSingle stage slurry pump, the nut can be lubricated with kerosene prepared in advance, or the nut can be gently knocked with a wooden hammer and then removed. This method can also be used in slurry pumps and other places.　　 Types of motors for deep well pumps　　In fact, it can only be opened or closed, and the action time when opening and closing is relatively short.Standard requirements,　　The two have certain commonalities. They are both submersible. As the name suggests, the pump is in an invasive state when running. The submersible slurry pump is a kind of submersible pump, but generally speaking people often say that the submersible pump refers to the clean water pump, such as the submersible pump for domestic water and farmland irrigation and pumping　　 One frequency converter with one slurry pump is adopted for installation. The specific transformation method is as follows: close the return valve, adopt the water level closed-loop control mode, install the liquid level sensor on the inner wall of the tank by the manufacturer of the slurry pump,ShemonaHH slurry pump, wide flow passage, strong sewage discharge capacity excellent material selection and strong corrosion resistance. It is suitable for conveying liquids containing solid particles, such as sandstone, cinder and tailings. So what are the requirements for its work? Let&#;s understand briefly.

　　First, the reason for the motor body: the wrong connection will make the temperature rise rapidly when the equipment is used; In addition, there may be some phase to phase short circuits between stator windings, so when the situation is relatively minor, the motor is only in local placesDiscount,　　 The standby submersible slurry pump shall roll the shaft / turn every week to make the bearing uniformly accept the static load and external oscillation. The building structure in the water pump room shall be reconstructed. Sound absorbing and isolating plates shall be installed around the wall and on the top of the machine room and fixed with light steel keel; The connecting holes between the machine room and other rooms are tightly blocked,　　That is, first, check whether the equipment operation noise is reasonable; second, check whether the alarm unit has leakage and overheating alarm signals; third,ShemonaCirculating hot water pipeline pump, record the flow and current of the water pump operation. If there is any problem in the above inspection, the cause shall be yzed and reported in time.　　The purpose is to inject liquid higher than . MPa from the water seal ring to prevent gas leakage into the pump when the suction inlet of the submersible slurry pump is in a vacuum state. When the water pressure in the pump is higher than . MPa, the sealing fluid .-. MPa higher than the pressure in the pump can be injected to seal and reduce leakageShemona,　　Therefore, the stator winding will be burnt out due to excessive temperature rise.　　Many people do not know much about the packing and sealing of equipment because of the equipment of mass and energy. Next, let&#;s learn about the packaging and sealing method of the equipment: packing sealing is very common in submersible slurry pumps. This method has good sealing performance, is easy to use, and effectively reduces the wear of the host and anti vibration kinetic energy　　 One frequency converter with one slurry pump is adopted for installation. The specific transformation method is as follows: close the return valve, adopt the water level closed-loop control mode, install the liquid level sensor on the inner wall of the tank by the manufacturer of the slurry pump, and use the PID adjustment of the frequency converter. When