SwarthOutdoor hydraulic lifting platformBasic knowledge of speed

According to the number of masts, it can be divided into: single mast lifting platform: a work platform supported by a single mast, which is an early form of elevator. The entire machine is light in weight and flexible in movement, suitable for single person operation. After condensation, it can enter general standard doorways and elevators in buildings.Compact in structure, it is a small lifting platform that can enter narrow passages and elevators.Swarth, roll and move the nut to the left end of the bolt and tighten the half round head bolt. Adjust the position of the collision rod up and down based on the lifting degree of the landing elevator platform so that when the lifting degree of the landing elevator platform exceeds the predetermined height, move the nut to collide with the collision rod and roll it clockwise. Push the limit switch contact to cut off the power supply.Equipped with a manual descent valve for emergency descent in case of power outage.Dijon,The scientific design schemes for elevators mainly include leveling and locking circuits, telescopic balance circuits, variable amplitude balance circuits, etc. In order to prevent sudden damage to the hydraulic system or pipelines of the platform due to accidents, we have designed different solutions for each system according to its different conditions.Check the hydraulic oil quality and level. When the lifting platform is raised to a high position, the hydraulic oil level should be - millimeters higher than the bottom of the oil tank. When the color of hydraulic oil darkens, the oil becomes sticky, or there are foreign objects such as gravel in the oil, how should the elevator be maintained? While we perform monthly maintenance on the elevator we should not forget to perform year-end maintenance on the elevator. Let's take a look at how the elevator should undergo year-end maintenance.The person in charge of the work should not only inspect the condition of the vehicle and the operators, but also be responsible for checking the terrain environment and whether the descent meets the requirements of safety technical measures or pre developed work plans. If there is any discrepancy, corresponding elevator measures should be formulated before starting work.

The equipment voltage is V DC, effectively ensuring personal safety.Ensure that the distance between the upper and lower limit switches and the limit iron is within the .-mm boundary between the limit switch handle and the upper and lower limit iron when the limit switch is disconnected. After adjusting the limit switch and limit switch appropriately, you can proceed with the assembly of the guide rail frame, attachment frame, and cable guide frame.The vehicle body should be grounded according to regulations, and the lifting operation should be commanded by the person in charge of the work. The person in charge should follow the standard signal and communicate with the lift operator. The signal emitted must be clear and accurate.Quality recommendation,The single mast elevator adopts high-strength and high-quality materials, which have the advantages of beautiful appearance, small volume, light weight,SwarthElectric small hydraulic lifting platform, smooth lifting, safety and reliability.At the end of the year, many customers called to inquire about elevators. During this time of year, various units need to hang lanterns etc. Many customers do not know how to choose a suitable elevator. Below is an answer for everyone. Lifts can be generally divided into three types: manual traction mobile lifting and lowering platforms: This type of lifting platform is cost-effective, cheap, and widely used, When moving, it requires manual traction or mechanical pulling from a car, and when lifting, it requires an external V or V power supply to lift.Check the rollers, intermediate shafts,SwarthHydraulic lifting platform factory, and bearings; Oil cylinder pin and bearing; Equality and wear of the hinge shaft and bearings of the boom; Fill the above components with oil. The service life of bearings can also be greatly enhanced.

Check the hydraulic oil quality and level. When the lifting platform is raised to a high position, the hydraulic oil level should be - millimeters higher than the bottom of the oil tank. When the color of hydraulic oil darkens, the oil becomes sticky, how should the elevator be maintained? While we perform monthly maintenance on the elevator, we should not forget to perform year-end maintenance on the elevator. Let's take a look at how the elevator should undergo year-end maintenance.supply,We are well aware of the harm of pressure, but how can we prevent water from seeping into the hydraulic system of the elevator? After reading this article, you may know that oil contains excessive water impurities which can rust the hydraulic components of the elevator, emulsify and deteriorate the oil, reduce the strength of the oil film,SwarthThe hydraulic lifting platform cannot be lifted, it is also important to note that when the oil storage tank is not in use, the cover should be tightened and placed upside down; Oil with high water content needs to be filtered multiple times, and the hydraulic oil of the elevator that is filtered each time needs to be replaced with a dry filter paper. In the absence of specialized instruments for detection, the oil can be dropped onto the hot iron plate, and no steam can be emitted before being added immediately. So when repairing the hydraulic system of aluminum alloy, be careful of the entry of moisture!Platform part: It is a steel structure platform that carries heavy objects, which can be closed (i.e. car type) or open, with guide rollers or guide shoes installed on both sides. The bottom of the platform can be connected to a lifting oil cylinder or a lifting shear fork shaped steel frame.Compact in structure, it is a small lifting platform that can enter narrow passages and elevators.Swarth,The single column elevator, equipped with a gantry cross frame accessory, is very suitable for maintenance work in cinemas, auditoriums, etc. The gantry frame is easy to assemble, labor-saving to operate, flexible to move, capable of crossing obstacles such as fixed seats with a height of up to m, and can operate stably on steps.Introduction to the characteristics, classification, and different uses of elevators: The overall use of high-strength aluminum profiles is refined. Due to the high strength of the profiles, they have the advantages of beautiful appearance, small volume, light weight, compact structure, convenient movement, stable lifting platform, easy operation, safety and reliability, making high-altitude operations more convenient and fast. They can walk quickly and slowly, can adjust speed, and have a column lifting system with a large load capacity, Strong stability, large platform area, and convenient implementation. It is the ideal high-altitude work equipment for modern enterprise safety production. It can be divided into single column, double column, three column, and four column.Single mast elevator Standard configuration of single mast elevator: platform height specifications: optional m, m, m, m; Power supply: single-phase AC (ACV/HZ) other forms can be optional; Movement method: manual traction.