Vishkov12CrMo alloy pipeStrengthen the training of R&D talents

After determining the reasonable pickling agent and polishing solution, it is very easy to carry out hot galvanizing for relevant alloy pipes. Use 'phosphating treatment' to degrease the pipes of electrolytic machine equipment, put them into the aqueous solution with zinc salt after pickling and passivation, connect the negative level of electrolytic machine equipment, put them into the cold-rolled steel plate in the direction corresponding to the pipes, and connect the switching power supply, If the current flows from the positive stage to the negative stage, a layer of zinc is deposited in the pipe.Plan scheme : for high carbon steel with carbon content of more than .% and high chromium alloy pipe with chromium content of no less than %, the interval is min.Vishkov,Classification by wall thicknessDetermined by the shape, the section modulus, moment of inertia and corresponding strength of I-beam are obviously better than those of ordinary I-beam with the same single weight. When used in metal structures with different requirements, it shows its superior performance in bearing bending moment, pressure load and eccentric load. Compared with ordinary I-beam, it can greatly improve the bearing capacity and save metal by % ~ %.Shaffield,X-ray or ultrasonic testing shall be carried out for repair welding of alloy pipe dead end welding of strip steel and circumferential seam. For the spiral welding of steel for the transportation of flammable general liquids, yibai%sx ray or ultrasonic testing shall be carried out. For the spiral welding of alloy pipes for the transportation of water, wastewater gas, heating steam and other general liquids, X-ray or ultrasonic testing sampling inspection (%) shall be carried out.→ compared with general section steel, it has the advantages of low cost, high precision and small residual stress. It does not need expensive welding materials and weld detection, and saves about % of the manufacturing cost of steel structure.Key technical characteristics of alloy pipe:

Small longitudinal crackAccording to the section shape, the steel pipe is divided into:The shape of I-beam is similar to that of H-beam. What is the difference between them?consumption,After determining the reasonable pickling agent and polishing solution, it is very easy to carry out hot galvanizing for relevant alloy pipes. Use 'phosphating treatment' to degrease the pipes of electrolytic machine equipment, put them into the aqueous solution with zinc salt after pickling and passivation, connect the negative level of electrolytic machine equipment, put them into the cold-rolled steel plate in the direction corresponding to the pipes, and connect the switching power supply, If the current flows from the positive stage to the negative stage, a layer of zinc is deposited in the pipe.In order to make the steel pipe workpiece have the required mechanical physical and chemical properties, in addition to the reasonable selection of materials and forming processes, heat treatment process is often essential. Steel is the most widely used material in the mechanical industry. The microstructure of steel is complex and can be controlled by heat treatment. Therefore, the heat treatment of steel is the main content of metal heat treatment. In addition, aluminum, copper, magnesium, titanium and their alloys can also change their mechanical, physical and chemical properties through heat treatment to obtain different service properties.Heating surface pipes, economizers, superheaters, reheaters, pipes for petrochemical industry, etc. for high-pressure boilers (working pressure is generally above MPa and working temperature is between ℃ ~ ℃)

Stages needing attention in the production and manufacture of alloy tubesQuality assuranceDehydrogenation solution: the alloy pipe shall be dehydrogenated after passivation treatment to avoid alkali embrittlementFirst, the two hole beam end space on the pier top shall be used to set the cast-in-situ transverse cantilever cantilever beam, on which the prefabricated micro bending plate shall be installed. The second is to erect prefabricated sidewalk beams in the cantilever part of the cantilever beam. The sidewalk beams of bridge openings on both sides are longer than the main beam, one end is supported on the cantilever beam of side pier, and the other end is supported on the special buttress on the embankment, which is to avoid widening the abutment.Due to the relatively high and narrow section size of ordinary I-beam and light I-beam, which makes it very limited in the scope of application. The use of I-beam shall be selected according to the requirements of design drawings.Vishkov,I-beam is a long strip steel with groove section, and its section shape is groove shape. China&#;s imports of I-beams are greater than its exports. The main producing areas are Tangshan Iron and steel, Baotou Iron and steel, Shangang, huangte,VishkovGh3039 superalloy tube, Maanshan Iron and steel, Xuanhua Iron and steel, Japan iron and steel,VishkovQ235B longitudinal welded pipe manufacturer, what we need to do now is to improve the production technology level of China&#;s production process of C-section steel, it is more conducive for C-section steel manufacturers to produce C-section steel products suitable for truck industry. Frame line crack