My java45 galvanized square pipePrecautions for installation operation

Square tube for automobile half shaft sleeve (gb-) is a high-quality carbon structural steel and alloy structural steel hot-rolled square tube for automobile half shaft sleeve and drive axle housing.Qb square tube, qb square tube, qb square tube, QB square tube, QB square tube and hot-rolled right angle square tube are of good quality and excellent quality. We have become a supplier of many enterprises. Qb square tube and I-beam are two products with different shapes. Under the condition of the same material, but their uses are very different. The shape is different. Qb square tube is a cuboid, the specific selection of steel depends on the requirements of the project. Square tube practical application square tube for structure (gbt-) is a square tube for general structure and mechanical structure.My java,The raw material for rolling square tube is round tube blank. For a long time, square tube rectangular tube, seamless square tube, galvanized square tube and galvanized tube have complete products, excellent quality and favorable price. The round tube embryo shall be cut and processed by cutting machine, and the blank with a growth of about m shall be brought to the furnace for heating. The billet is sent to the furnace for heating at a temperature of about degrees Celsius. The fuel is hydrogen or acetylene. The temperature in the furnace is the key problem. After the round tube billet is discharged from the furnace, it should be pierced through the pressure piercer. Generally, the more common piercer is the conical roll piercer. This piercer has high production efficiency, good product quality,My javaGalvanized plastic lined pipe, large perforation expansion and can wear a variety of steel grades.According to smelting classification and furnace type, A. open hearth steel: (a) acid open hearth steel; (b) Alkaline open hearth steel.Taian,Square tube production most square tube processing is square tube pressure processing, resulting in plastic deformation of the processed steel (billet, ingot, etc.). According to the square tube processing temperature, the square tube can be divided into cold processing and hot processing. The main processing of square tube includes: rolling: the gap (various shapes) between the square tube metal blank and the rotating roll , because of the compression of the roll, the material section is reduced and the length is increased. This is a common production method for producing square tubes. It is mainly used to produce square tube profiles, plates and tubes. It is divided into cold rolling and hot rolling.Zinc layer thickness: there is a great difference between cold galvanized square pipe and hot galvanized square pipe in galvanizing process; Cold galvanized square pipes are prone to & ldquo; Electric burning & rdquo; The color of this part is gray and the zinc layer is thick. It is easy to form a current dead angle at the corner resulting in an under current area. The zinc layer at this part is thin, and there is no zinc layer attached to the cold galvanized square pipe. The cold galvanized square pipe has no zinc lump and caking as a whole, but the overall zinc layer is thin, and the thickness of the outer wall zinc layer is μ m-μ m. The and outer walls of the hot-dip galvanized square tube are attached with zinc layer, and there will be water marks and a few zinc tumors, but the overall zinc layer is thick and the thickness of the zinc layer on the inner and outer walls of the square tube is -mu; M above. The nature of QB square tube!Stage ( & mdash; )

The inspection items, sampling quantity, sampling position and test of square tube shall be in accordance with the provisions of corresponding product standards. With the consent of the demander, hot-rolled square tubes can be sampled in batches according to the rolled root array.Section shape classification square tube is classified according to section shape: simple section square tube: square tube, rectangular square tube.After chemical pickling, the square tube can be well protected by electrolysis. These are simple ways to prolong the service life of the square tube, We only need to treat according to these, so that the square tube can bring us great help in the use process. The cold galvanized square tube is the principle of cold galvanizing on the square tube used to make the square tube have corrosion performance. Different from hot-dip galvanizing,My java160 galvanized square pipe, cold galvanizing coating is mainly carried out according to the electrochemical principle. Therefore, it is necessary to ensure the sufficient of zinc powder and steel, resulting in electrode potential difference, so the steel surface treatment requirements are very high.Quality inspection report, improve material rate and improve product quality. Seamless pipe can be divided into hot rolled pipe and cold rolled pipe according to different productionHigh density may not be obtained by simple pressurization, and insulation shall be carried out at the same time.The general delivery length of qb square pipe is mm-mm, mostly mm and mm. Qb square tube is allowed to deliver short length and non fixed length products not less than mm, or in the form of interface tube

The floating mandrel mill is in its heydayPromise and keep promise,Ferroalloy is an alloy composed of iron and silicon, manganese, chromium, titanium and other elements. Ferroalloy is the raw material for steelmaking. It is used as deoxidizer and alloy element additive for steel in square tube steelmaking.Polishing process of square tube square tube is widely used in our life, so in the subsequent application process, the requirements for square tube in many places are also quite strict, especially for surface treatment. Today, we briefly introduce how the polishing process should be carried out.Mechanical engineering, power plants, agricultural and chemical machinery, glass curtain walls, automobile chassis, airports, boiler construction, highway railings, housing construction pressure vessels, oil storage tanks, bridges, power station equipment, heavy transportation machinery and other welded structural parts with high load, etc. Process classification: according to the production process, square tubes are divided into hot-rolled seamless square tubes, cold drawn seamless square tubes, seamless square tubes and qb square tubes.My java,Stage ( & mdash; )Square tube is made of different materials. It needs qualified inspection by relevant staff before leaving the factory. Square tube has a wide range of uses. Its main field is not only the construction industry, but also can be seen everywhere in our daily life. The service life of square tubes is mainly affected by surface treatment. I will explain the specific operations of surface treatment of square tubes.Derusting grade for the construction process of epoxy,My javaGalvanized square pipe joint, ethylene, phenolic and other coatings commonly used for square pipes, and the depth of anchor grain can reach ~ & mu; m, which fully meets the requirements of adhesion between layer and square pipe The shot derusting process can meet the technical conditions of near white level (SA) with low operation cost and stable and reliable quality.