In tafilaDeep well submersible pumpWhat method is used for operation

　　Wheel, mixing impeller and other main flow passage parts are made of high wear-resistant raw materials, which are wear-resistant, corrosion-resistant,In tafilaISG single stage vertical pipeline pump,In tafilaSmall deep well pump, non clogging, and have strong sewage discharge capacity, and can effectively pass through large solid particles. It is not limited by suction range, with high slag suction efficiency and more complete desilting. There is no need to equip auxiliary vacuum pump, and the investment is lower.　　The water slurry pump is a widely used equipment. Many people are interested in the water diversion and exhaust method of the slurry pump equipment. Now let&#;s talk about the water diversion and exhaust method of the submersible slurry pump: the submersible slurry pump needs to pump out the water to form a vacuum, and then supply water,In tafila,　　 Motor disassembly: remove the base, thrust bearing, thrust disc, connecting seat of lower guide bearing seat, water deflector, take out the rotor, stator, etc.　　 During the installation of smooth bearing components, if the installation is correct, the smooth oil is appropriate,In tafilaBooster pipeline pump, the repair is timely, and the delivery life will be long, the repair personnel should regularly repair the bearing components, check the condition of the bearings and the smooth oil, and regularly add or replace the smooth oil during the work and the interval and writeBago,　　 Moreover, the processes of these two pumps are also different, and the sewage pump can generally be adjusted. Submersible pumps are generally used in some special or other places.　　The motor is scrapped. Moreover, because the length of the long shaft is generally fixed, the installation and use of the pump is troublesome, and the application occasions are subject to many restrictions.　　 The gas inadvertently entered in the equipment is discharged and good sealing performance is ensured.

　　Rate loss, firstly loosen the support cover, and then loosen the bearing seat. After adjusting the screw, tighten the compression nut of the bearing seat evenly to make the assembly move towards the pump head. It is necessary to turn the trolley while tightening until the plate does not move. Rotate according to the pump operationOnline consultation,　　The two have certain commonalities. They are both submersible. As the name suggests, the pump is in an invasive state when running. The submersible slurry pump is a kind of submersible pump but generally speaking, people often say that the submersible pump refers to the clean water pump, such as the submersible pump for domestic water and farmland irrigation and pumping　　Auxiliary mixing or spraying device shall be equipped for easier operation. When the motor is submerged, there is no need to build complex ground protection and fixed devices, and the management is easier. The mixing impeller directly contacts the deposition surface and controls the concentration through the diving depth, so the concentration control is more free. Equipment directly submerged　　Ordinary vertical motor can be used without waterproof, while the motor shaft and pump shaft of submersible slurry pump are coaxial, so the motor must be waterproof and sealed, and the motor and pump can be immersed in liquid at the same time; The vertical slurry pump is an early product, and the submersible slurry pump is a newly developed product according to the market demand

　　The purpose is to inject liquid higher than . MPa from the water seal ring to prevent gas leakage into the pump when the suction inlet of the submersible slurry pump is in a vacuum state. When the water pressure in the pump is higher than . MPa, the sealing fluid .-. MPa higher than the pressure in the pump can be injected to seal and reduce leakagequery,　　Balance of.　　Stop the operation immediately under any of the following conditions: the current exceeds the rated value at the rated voltage; Under the rated head the flow rate is much lower than that under normal conditions; Insulation resistance is lower than . megohm; When the dynamic water level drops to the pump suction; When the electrical equipment and circuit are out of specification　　It can improve the mechanical efficiency to a certain extent. Moreover, the molecular structure of the coating itself has good compactness, which can well isolate the air, water and other media from the pump impeller during use, and also reduce the corrosion and rust as much as possibleIn tafila, since the length of the long shaft is generally fixed, the installation and use of the slurry pump submersible are troublesome and the application occasions are limited. The submersible slurry pump is developed to adapt to increasingly complex working conditions and facilitate the use of users. Its use mode is more　　It needs to be replaced in case of damage, swelling and deformation, insufficient spring pressure, breakage etc.　　 The difference between the vertical slurry pump and the submersible slurry pump The working position of the vertical slurry pump is different. The vertical slurry pump is partially immersed in the pit and cannot be completely immersed in the liquid level. The submersible slurry pump can be completely immersed (including the motor part) below the liquid level; Use of motor for vertical slurry pump