TucsonFixed hydraulic lifting cargo elevatorWhat are the ways to use

Knowledge popularization of scissor-type fixed lifting platform Superior performance: equipped with safety devices to prevent overloading of the lifting platform; equipped with protection valves to prevent hydraulic oil pipes from breaking; equipped with emergency descending devices for sudden power failures; Lock safety device.It is best not to cover the aerial work vehicle and park the vehicle outside. If it is windy and rainy, the clothing will repeatedly slap the car paint, especially if the car blows sand on the clothes, it will draw many fine scratches on it. Because it will turn black over time. In addition, when the wind does not directly spray powder or clean the sand on the mechanism, but it should be washed with water, and prevent the sand particles on the paint surface from being scratched by the vacuum cleaner.Tucson,The pressure of the lifting platform is very important. When the general cargo is lifted, the pressure of the lifting platform will test the weight of the cargo. If it is overloaded, the general lifting platform will prompt. This is the role of protection, so now the lifting platform is pressed. pressurizer. Hydraulic machinery should remind everyone to pay attention to the following points: The precautions for the use of small lifting platforms are to look at the pressure. Their load capacity is very poor, and the size is small. When using it, it will It caused structural damage to the lifting platform, which we have said many times before.Regarding the cleanliness of the hydraulic station, is there any relevant rule requirement?Rio Negro,Hydraulic system: mainly oil cylinders, high-strength chrome-plated rods, Japanese NOK seals, self-made external integrated pump stations, oil pipelines, solenoid valves etc. The Japanese NOK seal used in the oil cylinder has good wear resistance,TucsonHydraulic lifting cargo elevator, which ensures that the oil cylinder series will not leak oil for a long time. The gear pump pumps the oil in the oil tank into the oil circuit and enters the oil cylinder, thereby driving the top of the rod and raising the equipment; The valve is used to adjust the oil output, the ascending and descending speed, and contains an emergency descending device to ensure that the guide rail hydraulic lifting platform can descend safely in case of an emergency.Outriggers: mechanical outriggers, hydraulic outriggers, ordinary hand-operated outriggers, pull-out outriggers.What are the maintenance rules for hydraulic lift machinery? The brakes of each mechanism should be checked frequently and the gap between the brake shoe and the brake wheel should be adjusted to ensure flexibility and reliability. There should be no dirt on the friction surface,Tucson3-meter cargo elevator, and if there is dirt, it must be washed off with gasoline or thinner.

Walking: assisted self-propelled,TucsonWhere is there a lift for goods, self-driving, and car modified.Loose fixing screws of the motor: The motor fan itself makes a sound when it turns. If the screws fixing the motor are loose, coupled with its own vibration, the motor collides with other parts in a way, so it makes a sound; the joints of the pin shafts are dry, iron The rigid friction between the parts and the iron parts will not only damage the parts but also produce abnormal noises, so I still want to emphasize again, pay attention to timely maintenance and frequent refueling; if the hydraulic lifting platform does not rise, there is air in the hydraulic oil, you can open it to exhaust If the hydraulic oil is solidified: just replace the hydraulic oil; oil leakage: check whether there is oil leakage at the joints of each oil pipe, if there is oil leakage, replace it in time; reverse the motor: check whether the wiring is wrong; (no Those who understand electricity, timely manufacturers of hydraulic lifting platforms)Today, the editor will talk about a series of safety devices and their uses on the guide rail hydraulic lifting platform.The cheapest,Low cost: The cost is much lower than that of the scissor-type mobile lifting platform, so when purchasing a lifting platform, you must consider the scope of use of the lifting platform, the frequency of work, the load and other factors to choose a lifting platform that suits the work requirements .What is the new price of a fixed lift? Professionally improve the quality assurance of the freight elevator factory. The preferential activities are in progress, and new and old customers are welcome to come to consult.Low cost: The cost is much lower than that of the scissor-type mobile lifting platform, so when purchasing a lifting platform, you must consider the scope of use of the lifting platform, the frequency of work, the load and other factors to choose a lifting platform that suits the work requirements .

The last thing to note is that, compared with the lifting platforms in some places, protective fences are generally added on the platforms. Since the lifting platforms are special equipment, the National Quality Inspection Bureau is very strict on this piece of inspection. All must be dismantled, so when the personnel ask you if you want to add a guardrail, don't blindly refuse, you must have the 'People's Republic of Special Equipment Manufacturing License' and the 'People's Republic of Special Equipment Installation, Transformation and Maintenance License' to produce, install and maintain. Therefore, you must ask whether the manufacturer has these two certificates.Free consultationThe surface of the brushes of each part should be kept clean, and the pressure of the brushes should be adjusted so that the area is not less than %. Professional elevator factory, large quantity favorably, high quality and low price. Fire-resistant-waterproof-high temperature resistant, durable, safe and reliable.The condition of the oil in each system of the elevator should be checked, and if it is found that the oil is foaming or turbid, it should be replaced in time. The performance of the professional elevator factory is stable, safe, reliable, and can be maintenance-free. The technical level has reached the domestic level and the international advanced level of similar products.Unscrew the screw on the dust-proof hole outside the flange of the elevator adjust the PCS system ring to align the side hole with the dust-proof hole, and tighten the inner hexagon. After that, remove the motor shaft key.TucsonWhat are the maintenance rules for hydraulic lift machinery? The brakes of each mechanism should be checked frequently and the gap between the brake shoe and the brake wheel should be adjusted to ensure flexibility and reliability. There should be no dirt on the friction surface, and if there is dirt, it must be washed off with gasoline or thinner.The safety device of the guide rail hydraulic lifting platform The mechanical part of the guide rail hydraulic lifting platform mainly includes the hydraulic system and the mechanical device.System: explosion-proof electronic control system, remote control system, P IC system.