TurkuFixed guide rail lifting cargo elevatorWhat is the chemical composition of

After the goods are transported, clean up the debris on the platform.Before the elevator manufacturer connects the motor to the elevator,TurkuGuide rail type simple lifting cargo elevator, please make the keyway of the motor shaft perpendicular to the tightening bolt. In order to ensure uniform force, please screw on the mounting bolts at any diagonal position first, but do not tighten them tightly, then screw on the other two mounting bolts at diagonal positions,TurkuProfessional guide rail type cargo elevator, and then tighten the four mounting bolts one by one. Finally, tighten the tension bolts. All tightening bolts need a torque wrench to fix according to the marked fixed torque data and check whether the lift and lifting platform are used.How should we check the construction site of the construction hoist? you know?Turku,The shafts in the middle of the support rods of the hydraulic lifting platform are inconsistent, causing the lifting platform to fail to work normally, the platform is severely damaged, and it has been put into the market. Caused a lot of accidents to take place, for the tilt detection, the detection of this link is not very concerned about for the majority of small enterprises, which is why there are such a large number of lifting equipment to have this problem. Problems with the oil cylinder and the power unit system are often caused by insufficient power and unqualified quality of the oil cylinder, which is also a problem that the enterprise itself needs to pay attention to.Pay attention to check whether there are any broken wires and loose strands in the wire ropes of each part. If it exceeds the relevant regulations,It is best not to cover the aerial work vehicle and park the vehicle outside. If it is windy and rainy, the clothing will repeatedly slap the car paint, especially if the car blows sand on the clothes, it will draw many fine scratches on it. Because it will turn black over time. In addition, when the wind does not directly spray powder or clean the sand on the mechanism, but it should be washed with water and prevent the sand particles on the paint surface from being scratched by the vacuum cleaner.Many people think that the strength of the elevator itself is relatively high when using the elevator, so they did not strictly follow the installation method in the manual during the installation process, and pay attention to the work The installation precautions corresponding to the environment should not be ignored. Correct installation, use and maintenance of elevators are an important part of ensuring the normal operation of mechanical equipment. Therefore, when you install the elevator, please be sure to strictly follow the installation and use related matters below, and assemble and use it carefully.The hydraulic lifting platform is mainly the pressure transmission of hydraulic oil to realize the lifting function. Its scissor mechanical structure makes the lift stable, and the wide operating platform and high carrying capacity make the high-altitude operation wide and suitable for many people work at the same time. It makes high-altitude operations efficient and secure.

What are the maintenance rules for hydraulic lift machinery? The brakes of each mechanism should be checked frequently and the gap between the brake shoe and the brake wheel should be adjusted to ensure flexibility and reliability. There should be no dirt on the friction surface, and if there is dirt, it must be washed off with gasoline or thinner.It is strictly forbidden to connect the wrong power supply to the motor of the lifting platform. Make sure that the voltage is v or v, do the daily cleaning work, and clean the dust and sundries on the motor in time.Unscrew the screw on the dust-proof hole outside the flange of the elevator, adjust the PCS system ring to align the side hole with the dust-proof hole and tighten the inner hexagon. After that, remove the motor shaft key.How many?,Check the limit switch to see if all the limit switches are loose. If so, please tighten them. Pay special attention to the ultra-high protection stroke of the hydraulic lifting platform to avoid accidents caused by the equipment exceeding the high safety height; check the pins (ear pins and center pins) Check whether the nuts, nuts, screws, etc. are loose, if any, should be reinforced immediately; ensure that the hydraulic lifting platform rises and falls smoothly; outriggers (for high-altitude operating platform)Unscrew the screw on the dust-proof hole outside the flange of the elevator, adjust the PCS system ring to align the side hole with the dust-proof hole, and tighten the inner hexagon. After that, remove the motor shaft key.The common types of lifts are simply introduced here for you. I hope you can learn more about this product. At present, this product can be said to be sold well in China, because many places need to use this product. Products that can be lifted and moved flexibly at the same time. Now companies that specialize in the production of this product combine a large-scale external publicity on the Internet. Friends in need can directly find the corresponding company on the Internet, and then simply learn about the models of these products and Information on performance and price can be purchased directly through the Internet.

It is strictly forbidden to switch the electric control switch with wet hands. Many people tend to ignore this detail. Although the safety voltage of the hydraulic lifting platform is below V, if you touch the power supply with your hands it may cause lifting failure in light cases, or electric shock accidents in severe cases.quality,The daily maintenance of the hydraulic lifting platform in normal use is essential, but even if there is normal maintenance on the equipment, any possible problem cannot be ignored, so in order to ensure that the process of using the hydraulic lifting platform for each operation What aspects do we need to check before operation? Today, the editor will give you a popular science.The guide rail type elevator is a kind of equipment for transporting heavy objects up and down. It has a very good application in factories, its daily maintenance and maintenance are very important,TurkuHydraulic lifting cargo elevator, because some small details If you don't pay attention, it will have a great impact on the operation safety of the equipment, so pay attention when doing the daily maintenance of the elevator.The use of elevators is not to maintain and overhaul after the equipment fails. It is necessary to maintain the equipment according to the correct maintenance and overhaul, and start with the preparation work to prevent all possible failures and accidents. I hope that the editor can summarize the knowledge points today. Help everyone.Turku,It is strictly forbidden for personnel to take the freight elevator to go up and down floors and climb.Precautions for elevator installation Keep the access road of the external construction elevator smooth and have enough parking space for equipment. When it is necessary to use a steam crane for auxiliary installation, it should be fully considered whether the site environment meets the operating conditions of the steam crane.When the freight elevator breaks down professionals should be invited to repair it, and the freight elevator cannot be altered without authorization.