Research OfficeOf hot dip galvanized square pipeIndustry structure needs to be adjusted

B. converter steel: (a) acid converter steel; (b) Basic converter steel. Or (a) bottom blown converter steel; (b) Side blown converter steel; (c) Top blown converter steel.Purpose of square tube the purpose of square tube includes construction, machinery, steel construction and other projects, shipbuilding, solar power generation support, steel structure engineering, electric products ( pieces)Research Office,× × ～ × × ～ × × ～ × × ～ × × ～ × × ～ × × ～ × × ～ × × ～ × × ～ × × ～ × × ～ × × Standard treatment of steps for preventing oxidation of ~ square tube square tube is a kind of metallic maintenance. The main components are iron and zinc. It is easy to have redox reaction in the air. Once the reaction occurs, many new substances have taken place, and the original characteristics have changed. However, in order to maintain the original relevant characteristics, anti-oxidation treatment is required. The direct reason is to prevent the square tube from reacting with the oxygen in the air, which is the way to isolate the oxygen in the air. Today, you can directly spray fluorocarbon paint on it; if alkyd antirust or red lead is used, it shall be cleaned with paint remover and sprayed with epoxy zinc rich or iron rich antirust paint again before fluorocarbon paint can be sprayed.The principle of straightening machine is that a disc is divided into two sides to clamp round steel straight lines. Professional square tube, square rectangular tube seamless square tube, galvanized square tube, galvanized tube, high price,Research OfficeHow much is a ton of galvanized rectangular pipe, on-site settlement, honest operation! The edge is one with radius r, and the other outer edge must be two equal diameters with radius R. The diameter of the reinforcement to be straightened is D, and the center distance between them is adjusted to R + R + D.Dzhalagash,Square tube heating process square tube calculates the chip thickness of workpiece. After each regrinding, the main drive AC motor spindle rotates stepless speed change AC motor feed capacity stepless speed change feed fast return to a constant value center system brush device hydraulic saw cutting system system system represents the quality RA flatness, large burr height cutting Chip length tolerance dimension: width and length . ~ .mm ~ m ~ ~ min kW ~ rpm ( kw ~ mmmin mmmin .kw .kw & times; kW S & mu; m . mm & plusmn; mm about mm about mm about mm high. The total weight of each billet square tube is seconds (including, pipe blank cutting, saw blade return, pipe blank discharge head and tail cutting time, which is composed of a fixed gear vibration reduction but excluding pipe blank transportation time). The large production capacity of the three saws is T / A. the pipe blank saw has a special reversing device (hydraulic servo device) to reduce vibration and improve the service life of the saw (only during feeding). The sawing machine has two devices distributed at the inlet and outlet (the input area is supported by roller table to ensure the bending of billet) The inlet end after sawing. Open it to ensure that the saw blade does not contact the blank when it returns. & mdash; feed saw gear & mdash; saw gear vibration reduction, as a movable vibration reduction to avoid the axial of the saw blade. & mdash; brush and sweep device & mdash; a driving brush and sweep device is installed at the bottom of the saw blade to clean the iron filings on the teeth and will not affect the service life of the saw blade. &Mdash; saw blade. In order to improve the service life of the saw blade, a small amount of high load agent container is atomized by air and poured on the saw blade without residue. & mdash; saw blade cooling device. A special nozzle is used to spray cold air at - oC on the saw blade. The cut-off blank is transferred to the buffer chain in front of the loader after passing through the outlet roller table and weighing device (Note: # before sawing, there is a feeding bench for single size billets that need to be cut, and after weighing, there is a feeding bench for returned billets). The buffer transfer chain transports the billets to the lower roller table of the loader. The billets are turned over from the chain to the roller table by the turnover hook. The weighed qualified billets are loaded into the annular furnace by the loader and the weighed unqualified billets are transported from the roller table to the removal bench for removal.If the test results of square tubes fail to meet the provisions of product standards, the unqualified ones shall be selected, and double the number of samples shall be taken from the same batch of square tubes for re inspection of unqualified items. If the re inspection results (including any index required by the test of the project) are unqualified, the batch of square tubes shall not be delivered. If the following inspection items fail to pass the preliminary inspection, re inspection is not allowed: A. There are white spots in the low magnification; b. Microscopic.Generally, chemical and electrolytic methods are used

A. square tube structural steel: (a) high quality carbon structural steel; (b) Alloy structural steel; (c) Spring steel; (d) Easy cutting steel; (e) Bearing steel; (f) High quality structural steel for specific purposes.With the development of economy, there are a lot of demands for project construction,Research OfficeGalvanized steel prices today, which leads to the continuous increase of square pipe. The of square pipe is more complex. Great efforts should be made in the selection of raw materials, structured treatment and so on.Welding is a synthetic gradient material, which can be used as solder to weld special-shaped materials in order to overcome the mismatch of chemical, mechanical and physical properties between base metals.Quality documents,Because the green billet can be pressed into any shape, it is easy to weld the square tube into difficult products.Section shape classification square tubes are classified according to section shape: simple section square tubes & mdash& mdash; Square tube, rectangular tube and complex section square tube & mdash& mdash; Surface treatment classification of flower shaped square pipe, open square pipe, corrugated square pipe and special-shaped square pipe square pipe is divided into hot-dip galvanized square pipe, electro galvanized square pipe oil coated square pipe and pickling square pipe according to surface treatment. Square pipe is classified according to purpose & mdash& mdash; Square tubes for decoration, machine tools and equipment, machinery industry, chemical industry, shipbuilding, automobile, steel beam and column and special purpose are classified by wall thickness & mdash& mdash; Super square tube, square tube and thin-walled square tube plasticity refers to the ability of metal materials to produce plastic deformation (deformation) without deformation under load.Ferroalloy is an alloy composed of iron and silicon, manganese, chromium, titanium and other elements. Ferroalloy is the raw material for steelmaking. It is used as deoxidizer and alloy element additive for steel in square tube steelmaking.

There are sets of MPM and sets of MRK pipe mills in the world. Strength refers to the function of qb square tube data being destroyed under static load (appropriate plastic deformation or fracture). Because the action forms of load include tension, contraction, meandering, shear and so on, because the strength is also divided into tensile strength, compressive strength, flexural strength, shear strength and so on. There is often a definite connection between various strengths. Long term square tube, square rectangular tube, seamless square tube, galvanized square tube and galvanized tube have no turnover to avoid price difference, and the price is % higher than the market price! The price of more than one ton is higher! In normal use, tensile strength is often taken as the fundamental strength gauge needle.Packaging strategy,Precision inner diameter square tubes for hydraulic and pneumatic cylinders (gb-) are cold drawn or cold-rolled precision square tubes with precision inner diameter for hydraulic and pneumatic cylinders.Large diameter welded square pipe for low pressure fluid transmission, Standard No.: gbt-. Representative material: qab grade. It is mainly used to transport low-pressure fluids, such as water, sewage,Research Office25 price of galvanized square pipe, gas, air and heating steam.Stage ( & mdash; )Research Office,B. tool steel: (a) carbon tool steel; (b) Alloy tool steel; (c) High speed tool steel.Hardness hardness is a pointer to measure the hardness and softness of metal materials. At present, the hardness method is commonly used to measure the hardness in production. It uses the indenter with fixed geometry to measure the hardness value of the metal material surface tested under fixed load according to the degree of hardness.Spraying (throwing) derusting spraying (throwing) derusting is that the high-power motor drives the spraying (throwing) blade to rotate at high speed, so that the steel sand, steel shot, iron wire section, minerals and other abrasives can be sprayed (thrown) on the surface of the square tube under the action of centrifugal force, which can not only completely remove rust, oxides and dirt, but also the square tube under the violent impact and force of abrasives, It can also achieve the required uniform roughness.