El PasoScissor fork hydraulic lifting platformCompanies need to consider the balance of interests

There is a phenomenon of self stopping when running up and down. Due to poor contact of the safety protection switch, it is easy for hydraulic cargo elevator manufacturers to cause this problem.Vehicle mounted lifting platform is widely used for high-altitude operations in hotels, buildings, airports, sports venues, workshops, warehouses, and other places; It can also be used as temporary high-altitude lighting, advertising, etc.El Paso,Advantages of geotechnical engineering: There is no need for a computer room above the shaft, and the top floor height can reach over meters.The manufacturer of hydraulic cargo elevators will tell you about the knowledge of specialized lifting platforms for unloading.LouresIf the circuit of the device is not disconnected or lowered, it is necessary to check the fuse for repair and replacement.The hydraulic lifting platform is a manually movable type,El PasoDouble shear hydraulic lifting platform,El PasoFixed hydraulic elevator, and the lifting power of the platform is a two machine or three-phase power supply. It has manual and electric power, and is also equipped with a hand pump for use in case of power outage. This series of platforms have the characteristics of flexible movement, stable lifting, and easy operation, and are mainly used in factories, government agencies, commercial stores, and the construction and decoration industry.Introduction to the unloading lifting platform: The unloading lifting platform is a specialized auxiliary equipment used in conjunction with forklifts for cargo loading and unloading. With it, forklifts can directly drive from the ground into the interior of car compartments for batch loading and unloading operations. The warehouse unloading platform products use manual hydraulic power and do not require power supply. Only one person needs to operate to achieve safe and fast loading and unloading of goods. It can reduce a lot of labor, improve the efficiency of loading and unloading operations, speed up the flow of materials, and obtain greater economic benefits.

Selection of the location of the loading and unloading lifting platform In order to reduce the cost of material handling, the location of the platform should be selected to minimize the distance of the handling tools and vehicles in the factory. It is much easier to move a fully loaded transport vehicle to a designated location outside the building than to transport the loaded materials one by one to the designated location indoors. When selecting a platform location, full consideration should be given to the production process and operational needs of the factory. There are two modes of platform layout: merging: loading and unloading on the same platform.In winter, heating rest areas should be set up near the construction area if necessary. Heating equipment should be managed by dedicated personnel and attention should be paid to fire prevention.I believe many people want to know about the maintenance issues of guide rail hydraulic lifting platforms, as it is related to their service life. During use, frequently check the connection of each part. If loose, tighten it. When the body is under pressure, the tightness of the connecting bolts of the body should be checked (the pressure state that can be used). All connecting shafts should have split pins and hydraulic cargo elevators should be fully opened.production costs,Each brush should be kept clean on its surface, and the brush pressure should be adjusted to ensure that its area is not less than %.Separate: Loading and unloading on different platforms.There are many reasons for unstable workbench descent, such as overload, unstable support, severe eccentric load, hydraulic oil impurities etc. In response to the above reasons, it can be solved by reducing the load, adjusting the center of gravity of the load, and replacing hydraulic oil wholesale for hydraulic cargo elevators.

The guide rail type elevator has a structure of a straight top oil cylinder. The linear operation of the oil cylinder pulls the transmission chain, driving the lifting of the table to complete the operation. The guide rail type elevator is a popular form of cargo elevator in recent years, with the advantages of higher lifting height, stable operation, and simple maintenance compared to the scissor fork type elevator.Management Department,The elevator is evenly distributed at any position on the guide rail at % of the maximum load capacity, and should be stable at the maximum lifting height.In on-site hydraulic elevators, it is difficult to detect the rising position, middle position, impact noise, and oil film leakage of hydraulic cylinders. Field observations have shown that the excessive lifting speed of the hydraulic cylinder has led to an increase in failure rate, seriously affecting production efficiency. The unstable hydraulic lifting requires an analysis of the hydraulic oil flow rate. Hydraulic pressing oil has poor quality and contains a large amount of impurities, which can also prevent slow and unstable lifting. In addition, there are other reasons: lifting the composition of the hydraulic ring. Oil pump, safety valve, directional valve, directional valve, one-way throttle valve (without throttling), and the pilot valve and valve seat are matched without spring deformation or incorrect installation. The remote control port has excessive oil flow, low or high hydraulic oil viscosity, and resonance occurs with components in the circuit. Troubleshooting: Strengthen sealing, repeatedly adjust the pressure exhaust and clean the valve body several times, repair or replace the spring Make the damping hole unobstructed, reduce the flow of the remote control port, and other components. The pressure setting of other components should not be similar to the pressure setting of the relief valve. . The noise of the elevator pipeline is usually caused by excessive dead bends or loose fixed sleeves in the hydraulic pipeline.El Paso,Load bearing capacity: The lifting platform is placed on a horizontal support surface, and the workbench is evenly loaded to % of the maximum load capacity. After lifting times, each load-bearing component must not have deformation or cracks.Do not use hydraulic lifting equipment with malfunctioning issues. The problem should be resolved before carrying cargo.The manufacturer of the hydraulic cargo elevator tells you the reason and cleaning method: Reason: Overload cleaning method: Reduce the load to clean. Reason: The return valve is not closed. Cleaning method: Tighten the return valve to clean. Reason: The one-way valve of the manual pump is stuck and the return valve is malfunctioning. Cleaning method: Unscrew the bolt at the valve port of the oil pump, conduct maintenance, cleaning, and replace the cleaning hydraulic oil to clean.