MaydayFixed electric hydraulic lifting platformCommon raw materials

Check valve leakage: If the natural wear of the check valve exceeds the specified value after long-term use, it will cause leakage. Disassemble and clean the check valve, when all hydraulic cylinders in the system are extendedConsidering the oil level in the oil tank and ropes should be used to tie or hang them to avoid injuring workers or scaffolding below.Regularly inspect the hydraulic lifting equipment of the upper and lower materials to ensure the safety of the rail type elevator and the safety of the material supply to the rail type lifting platform.IfraneIt is not allowed to throw tools and materials up and down, the oil level in the oil tank should not be lower than the Z-low oil level, and when the oil cylinders retract, the oil level should not be higher than the Z-high oil level. In fact, most manufacturers have noticed the above issues. The reason for the introduction is that most users can learn more about the equipment itself when using elevators, in order to facilitate equipment maintenance. Hydraulic cargo elevator manufacturers sincerely hope that you choose a legitimate manufacturer when purchasing elevators, to avoid any worries about after-sales service.Motor not running: Check all components of the motor for damage and check if there are any problems with the circuit and wiring.Therefore, the wholesale manufacturers of hydraulic elevators remind that there are three main ways to adjust the speed control circuit: throttling speed control circuit: quantitative pump oil supply, using flow valves to adjust the flow in and out of the actuator to achieve speed control; In the volume throttling speed control circuit, the oil is supplied by the pressure limiting variable pump, and the flow rate into the actuator is adjusted by the flow valve to adapt the flow rate of the variable pump to the regulated flow rate of the speed control valve.

The manufacturer of hydraulic cargo elevators will tell you about the knowledge of specialized lifting platforms for unloading.Any work carried out at a height of meters or above should be considered as work at height. Any work that can be done in advance on the ground must be done on the ground to minimize high-altitude operations.Considering the oil level in the oil tank, the oil level in the oil tank should not be lower than the Z-low oil level, and when the oil cylinders retract, the oil level should not be higher than the Z-high oil level. In fact, most manufacturers have noticed the above issues. The reason for the introduction is that most users can learn more about the equipment itself when using elevators, in order to facilitate equipment maintenance. Hydraulic cargo elevator manufacturers sincerely hope that you choose a legitimate manufacturer when purchasing elevators, to avoid any worries about after-sales service.The cost is reasonable,MaydayAluminum alloy hydraulic lifting platform,Reason: Cleaning method for internal leakage in the oil cylinder: Replace the sealing element of the oil cylinder. The lifting platform does not lower. Reason: The lowering valve is malfunctioning. Cleaning method: When pressing the lowering button, check whether the lowering valve is powered on. If there is no electricity, clean it as much as possible; If there is power, clear the malfunction of the lowering valve itself or replace the lowering valve. The sliding valve should be kept clean and.Remember not to overload, overload is the root cause of many faults.The use of cleaning oil and the brand used in the system

Motor not running: Check all components of the motor for damage and check if there are any problems with the circuit and wiring.new product,MaydayMobile hydraulic lifting platform/lifting platform,The classification of lifting platforms is as follows: they are divided into mobile lifting platforms, automatic lifting platforms, hydraulic lifting platforms, folding arm lifting platforms, and sleeve type lifting platforms according to their different modes of movement.Based on the foundation plan, pay attention to alignment, leveling, and alignment to ensure the foundation level and various usage requirements. The access road for external construction elevators should be flat and have sufficient space for equipment parking.What are the methods for reducing shaking on lifting platforms? Reducing the shaking of the lifting platform can reduce the psychological obstacles of the operators, ensure the smooth progress of the operation, do not operate blindly. Lifts are widely used in many places, and their working principles vary. Today, we will analyze the working principles of elevators. The types of elevators are generally divided into the following: fixed elevators,MaydayFixed hydraulic elevator, This type of elevator uses hydraulic oil cylinders and pump stations to transmit power, in the form of a scissor fork type. According to customer requirements, the length of the support rod for the scissor fork, the number of layers, the angle of the angle axis, and the expansion and contraction of the oil cylinder complete the lifting operation. Its advantages are large load-bearing capacity, stable lifting, and high safety.Mayday,The electromagnetic coil of the electromagnetic directional valve is not firmly fixed, and frequent separation and suction can also produce high noise.Remove the hydraulic oil tank filler cap, filter cover, inspection hole, hydraulic oil pipe and other parts to avoid dust when removing the system oil pipe. Clean the disassembled parts before opening them. When disassembling the hydraulic oil tank filler cap, first remove the soil around the tank cap, loosen the tank cap, and remove any remaining debris from the joint (do not rinse with water to prevent water from seeping into the tank). After confirming cleaning, open the tank cap.Remember not to overload, overload is the root cause of many faults.