BakersfieldSelf propelled scissor fork lifting platformWhat are the production characteristics of

Check the smooth steel wire rope and various fasteners, if there is excessive wear, it is necessary to replace themQuarterly maintenance: Check the items checked each monthBakersfield,Low failure rate: Due to the use of advanced hydraulic systems and good methods, the failure rate of elevator operation can be minimized. Low power consumption: When the hydraulic elevator descends, it is driven by the pressure generated by its own weight, which greatly saves energy.Check the safety interlocking equipment of the first cut door of the hanging cageMlimba,Regularly check the connection of each part and tighten it if there is any looseness. The tightness of the body connecting bolts should be checked when the body is under pressure (the rotating arm can be used to cause compression)The lifting stage can provide real-time information on the operation of the entire vehicle, avoiding relying solely on the experience of operators to coordinate with each other, and improving the reliability and safety of the system. The definition of safety zone is very important because the lifting stage has a large range of movements, and it must be accurately calculated. The lifting stage has two structurally separate systems,BakersfieldCar mounted aluminum alloy elevator, the ground turntable and the high-altitude work bar. However,BakersfieldMobile lifting platform, for various movements on the vehicle, it is also an interconnected system, which needs to consider the priority of operation, system redundancy, and safety assurance of actions.What are the functions of anti rust primer for warehouse cargo elevators?

Clean and inspect the crown wheel frame assembly, correct or replace with new partsDrivers should be responsible for supervising the uniform distribution of items transported by the platform on the platform as much as possible to prevent partial loading and prohibit overloading. Platform does not allow　　?? The supervision unit shall effectively fulfill its safety responsibilities, and if any potential production safety accidents are found, it shall require the installation unit and the user unit to rectify within a specified period of time. If the installation unit and the user unit refuse to rectify, they shall promptly report to the construction unitCreate brilliance,The lifting stage can provide real-time information on the operation of the entire vehicle, avoiding relying solely on the experience of operators to coordinate with each other, and improving the reliability and safety of the system. The definition of safety zone is very important because the lifting stage has a large range of movements, and it must be accurately calculated. The lifting stage has two structurally separate systems, the ground turntable and the high-altitude work bar. However, for various movements on the vehicle, it is also an interconnected system, which needs to consider the priority of operation, system redundancy, and safety assurance of actions.Check the oil level of the gearbox and make up for new oil if necessaryCheck the fastening status of the wall bracket, support rod, and bolts and retaining rings between the lifting cargo elevator and the bridge. If they are loose or displaced,BakersfieldHydraulic aluminum alloy lifting platform, they should be checked and tightened

Check the smooth steel wire rope and various fasteners if there is excessive wear, it is necessary to replace themTrustworthy,Check the protective cable condition of the cable guide frameVibration aging treatment and effect judgment: According to the aging process plan after setting the support points and vibration pickup points of the workpiece, and use the manual function of the equipment to test the vibration. It is determined that around revolutions is the resonance frequency of the component. The amplitude generated by the eccentric gear of the exciter in the fourth gear can meet the vibration processing requirements of the foundation seat, so the excitation force is selected as the fourth gear.Check the safety interlocking equipment of the first cut door of the hanging cageBakersfield,The wear rate is fast, and due to factors such as processing, assembly, and adjustment of new machine components, the friction surface is rough, and the surface pressure condition is uneven. During the operation of the machine, the concave and convex parts on the surface of the parts are intertwined and rubbed against each other. The metal debris that falls off from the grinding process, in turn, acts as abrasive and continues to participate in friction, further accelerating the wear of the mating surface of the parts. Therefore, during the running-in period, it is easy to cause wear on components (especially the mating surface), with a fast wear rate. At this point if overloaded, it may cause damage to the components and lead to early failures.Check if the orientation of the upper and lower limit blocks on the guide rail frame is correctThe cleaning oil for the hydraulic system must use hydraulic oil of the same brand as the system used, with an oil temperature between and ℃. Use a large flow rate to remove impurities from the system as much as possible. The hydraulic system needs to be cleaned repeatedly three times or more. After each cleaning