FenyangElectric hydraulic fixed lifting platformHow to break through the traditional marketing pattern

Ensure that there is a suitable power supply at the installation site, and separate maintenance of the distribution box is required. The distribution box should have a leakage switch, and the hydraulic cargo elevator construction site should be equipped with a fire extinguisher to prevent welding operations from causing fires. When selecting a leakage switch, it should be suitable for the operating power.Users should arrange dedicated personnel to operate hydraulic elevators, formulate usage details and safety precautions for hydraulic elevators based on their own situation, and hang them on theFenyang,One of the executing components of the hydraulic cargo elevator system is the hydraulic cylinder. The hydraulic cylinder is responsible for linear lifting or retraction. Its characteristics are light weight, high power, simple structure, convenient maintenance, low motion inertia, frequent commutation, and convenient remote control. Hydraulic cylinders are widely used in various single acting hydraulic cylinders as an example to analyze the conversion of hydraulic energy into mechanical energy for linear motion.Therefore, the wholesale manufacturers of hydraulic elevators remind that there are three main ways to adjust the speed control circuit: throttling speed control circuit: quantitative pump oil supply, using flow valves to adjust the flow in and out of the actuator to achieve speed control; In the volume throttling speed control circuit, the oil is supplied by the pressure limiting variable pump,FenyangMicro hydraulic lifting platform, and the flow rate into the actuator is adjusted by the flow valve to adapt the flow rate of the variable pump to the regulated flow rate of the speed control valve.San-Rafael-Abajo,Separate: Loading and unloading on different platforms.Considering the oil level in the oil tank, when all hydraulic cylinders in the system are extended, the oil level in the oil tank should not be lower than the Z-low oil level, and when the oil cylinders retract, the oil level should not be higher than the Z-high oil level. In fact, most manufacturers have noticed the above issues. The reason for the introduction is that most users can learn more about the equipment itself when using elevators, in order to facilitate equipment maintenance. Hydraulic cargo elevator manufacturers sincerely hope that you choose a legitimate manufacturer when purchasing elevators, to avoid any worries about after-sales service.Electrical equipment or component failures. Hydraulic elevator manufacturers tell you that the main reasons for high noise generated by electric motors are: bent or severely worn motor rotors, or damaged bearings, which cause electric motors to sweep and produce noise; The cooling fan of the electric motor is damaged or not firmly fixed, resulting in high noise; The electric motor is not firmly fixed and can also cause vibration, producing high noise.

There is noise inside the hydraulic cylinder. When replacing the hydraulic oil, there was air in the hydraulic cylinder due to an operational error. Under high pressure, it is easy to generate cavitation and high-frequency noise. When the rod is bent or replaced with a new seal, the new seal is too tight, which can also produce significant noise. If it is a problem of tight sealing, the noise can be reduced after running in for a period of time. If the rod is bent, it needs to be corrected. In addition, hydraulic pipelines should use hoses as much as possible, even when arranging pipelines, it can reduce vibration and noise, with a focus on checking the hydraulic pipes and joints, oil cylinders, and hydraulic valve connections. If hydraulic oil leaks, replace them with composite pads or disturb unprocessed raw materials.An inverter can also generate high noise. When the power supply voltage is lower than % of the rated voltage, the short circuit ring of the iron core of the device breaks, the surface of the magnetic yoke and armature is skewed dust or rust is poor, and the device will produce; Buzz&# quo; Noise.system,The precautions to consider when selecting a hydraulic lift oil tank include: considering the structure of the oil tank, the partition in the traditional oil tank cannot settle dirt. A vertical partition should be installed along the longitudinal axis of the oil tank, with a space left between one end of the partition and the end plate of the oil tank to connect the gaps on both sides of the partition. The inlet and outlet of the hydraulic pump are arranged on both sides of the partition at the disconnected end, so that the distance Z between the inlet and return oil is far,FenyangFoot hydraulic lifting platform vehicle,Fenyang10 meter hydraulic lifting platform, The hydraulic oil tank has more heat dissipation effect.The combined platform is often used in small workshops with small volume of goods. However because this platform needs to complete two functions at the same time, it inevitably increases the distance of handling tools/vehicles in the workshop.The elevator is evenly distributed at any position on the guide rail at % of the maximum load capacity, and should be stable at the maximum lifting height.

Introduction to the unloading lifting platform: The unloading lifting platform is a specialized auxiliary equipment used in conjunction with forklifts for cargo loading and unloading. With it, forklifts can directly drive from the ground into the interior of car compartments for batch loading and unloading operations. The warehouse unloading platform products use manual hydraulic power and do not require power supply. Only one person needs to operate to achieve safe and fast loading and unloading of goods. It can reduce a lot of labor, improve the efficiency of loading and unloading operations, speed up the flow of materials, and obtain greater economic benefits.OK or not?,To consider its capacity, generally mobile equipment takes - times the high flow rate of pump Z, and fixed equipment takes - times.The manufacturer of hydraulic cargo elevators tells you the reason for the instability of hydraulic lifting equipment. Hangzhou hydraulic cargo elevator equipment has always had good stability, mainly used for heavy types of goods. However during use, Hangzhou hydraulic cargo elevators may inevitably encounter some faults during the lifting process, such as very unstable conditions. What is the reason for the instability of the elevator? How to solve these problems?This paper briefly introduces some matters needing attention in the selection of oil tank for hydraulic elevators. The main functions of the hydraulic oil tank for elevators in the hydraulic system of elevators and hydraulic elevators and other hydraulic machinery are oil storage, separation of air contained in oil and elimination of foam.Fenyang,Aluminum alloy elevators are different from other forms. This type of elevator is made of aluminum alloy material, which is lightweight and has a more beautiful appearance. The disadvantage is that it has a light load capacity and is only suitable for simple high-altitude maintenance work, and can only provide support for - people.When disassembling and adjusting the reverse organization of the equipment, attention should be paid to ensuring that the centerline of the reverse organization reducer is parallel to the centerline of the gear, carefully implement the special construction plan for installation and construction