GirardotStainless steel pipeStrengthen personal protection

Series & mdash; Martensitic precipitation hardening stainless steel.In the building water supply pipe system, due to the end of the glorious history of galvanized steel pipe, various new plastic pipes and composite pipes have developed rapidly, but various pipes still have some deficiencies in varying degrees, which are far from fully meeting the needs of water supply pipe system and the national requirements for drinking water and related water quality. Therefore, relevant experts: building water supply pipes will eventually return to the era of metal pipes. According to foreign application experience stainless steel pipe is recognized as one of the pipes with good comprehensive performance in metal pipe.Girardot,The heat-treated alloy should be DEG at low temperature; Annealing treatment at the temperature of F,GirardotStainless steel water supply pipe, then rapid cooling and water quenching. This treatment is applied to solid melt annealing and stress relief. Stress relief treatment, such as below DEG; F, which is easy to lead to the precipitation of harmful metal or non-metallic phases.AUSTENITIC FERRITIC duplex stainless steel on the basis of austenitic stainless steel, appropriately increase Cr content and reduce Ni content, and cooperate with remelting treatment. High prices, various specifications of stainless steel plates, stainless steel coils, stainless steel belts and stainless steel tubes are supplied in time and cost-effective. It has become the preferred brand for many wire products. Welcome to buy! Stainless steel with duplex structure of austenite and ferrite (including ~ % & Delta; - ferrite) can be obtained. Typical steel grades include crniti, CrNiTi, ocrnimoti,Girardot201 stainless steel welded pipe, etc. Duplex stainless steel has good weldability, no heat treatment is required after welding, and its tendency of intergranular corrosion and stress corrosion is also small. However, due to the high Cr content, it is easy to form & sigma; Pay attention when using.Buea,High frequency welding high frequency welding: with relatively high power supply, it can reach a higher welding speed for steel pipes with different materials outer diameter and wall thickness. Compared with argon arc welding, it is more than ten times its high welding speed. Therefore, stainless steel pipes for common use have a higher consumption rate. Due to the high speed of high frequency welding, it is difficult to remove burrs in welded pipes. At present, high frequency welding Welded stainless steel pipe can not be borne by chemical and nuclear industries, which is also one of the reasons.Austenitic stainless steel. It contains more than % chromium, about % nickel and a small amount of molybdenum, titanium, nitrogen and other elements. Good comprehensive performance and resistance to corrosion of various media.For more than years, such as the Chrysler Building in New York City. However, in many other applications, the role of stainless steel is not so eye-catching, but in the aesthetics and performance of buildings For example,GirardotPrice of stainless steel pipe, because stainless steel has more wear resistance and pressure resistance than other metal materials of the same thickness, it is the preferred material for designers when building sidewalks in places with large population flow.

The intergranular corrosion of austenitic stainless steel can be prevented by adding Ti, Nb and other elements that can form stable carbides (tic or NBC) and avoiding the precipitation of crc on the grain boundary.Under plasma arc cutting corrosion conditions, there are dust containing other metal elements or attachments of dissimilar metal particles on the surface of stainless steel. In the air, the condensate between the attachments and stainless steel connects them into a micro battery, which causes electrochemical reaction and the protective film is affected, which is called electrochemical corrosion.Stainless steel seamless steel pipe for structure (instead of gbt-)Job description,The protection mechanism of stainless steel backing wire + TIG process is that the back weld is protected by the metallurgical reaction of slag produced by welding wire melting and its alloy elements, and the front weld is protected by argon, slag and alloy elements.Austenitic stainless steel has good resistance to uniform corrosion, but there are still the following problems in local corrosion resistance: intergranular corrosion of austenitic stainless steel. Austenitic stainless steel will have intergranular corrosion when it is kept warm at ~ ℃ or cooled slowly. The higher the carbon content, the greater the tendency of intergranular corrosion. In addition, intergranular corrosion also occurs in the heat affected zone of the weldment. This is due to the precipitation of Cr rich CrC on the grain boundary. The chromium poor area is formed in the surrounding matrix, which is caused by corrosion of the primary cell. This intergranular corrosion phenomenon also exists in the ferritic stainless steel mentioned above.The best way to improve the quality of stainless steel pipe fittings is to change the process from ingot to billet. Due to the improvement of continuous casting process, with the cooperation of other types of work, and the argon arc welder shall have the certificate issued by relevant departments.analysis,Production process of stainless steel welded pipe: raw material - strip - welded pipe - end repair - polishing - Inspection (spray printing) - Packaging - shipment (warehousing) (decorative welded pipe).The width of coiled material is variable, including mm.mm.mm.mm.mm.mm, etc. it can also be divided according to customer requirementsSection shape stainless steel pipe can be divided into round pipe and special-shaped pipe according to the section shape. Special shaped tubes include rectangular tubes, rhombic tubes, hexagonal tubes octagonal tubes and various cross-section asymmetric tubes. Special shaped pipe is widely used in various structural parts, tools and mechanical parts. Compared with circular pipe, special-shaped pipe generally has large moment of inertia and section modulus, and has large bending and torsion resistance, which can greatly reduce the structural weight and save steel.Girardot Series & mdash; Martensitic precipitation hardening stainless steel.Chloride ions exist in the service environment. Chloride ions exist widely, such as salt, sweat, sea water, soil, floating rust of iron foam and so on. Stainless steel corrodes rapidly in the presence of chloride ions, even more than ordinary low carbon steel. Therefore, there are requirements for the service environment of stainless steel, and it is necessary to remove dust frequently and keep it clean and dry. (in this way, we can give him a & ldquo; improper use & rdquo;) there is an example in the United States: an enterprise uses an oak container to contain a solution containing chloride ions. The container has been used for nearly years. The ninetieth generation of the last century plans to replace it. Because the oak material is not modern enough, the container leaks due to corrosion days after it is replaced with stainless steel.Raw materials -- strip splitting -- welded pipe making -- heat treatment -- Correction -- straightening -- end repair -- pickling -- Hydrostatic Test -- Inspection (spray printing) - packaging -- delivery (warehousing) (pipes for welded pipe industrial piping).