SerikPrice of 16 cm I-beamWhat problems should be paid attention to during operation

With the development of steel structure buildings, only I-beam is not enough, that is, thickened I-beam, which is easy to lose stability for load-bearing columns.Whether I-section steel is ordinary or light, due to the relatively high and narrow section size there is a large difference in the moment of inertia between the two main sleeves of the section. Therefore, it can only be directly used for members bent in the plane of their web or form lattice stress members. It is not suitable for axial compression members or members with bending perpendicular to the web plane,SerikDirect sales of Q345B welded pipe manufacturers, which makes it very limited in the scope of application.Serik,Galvanized pipe is a name for square pipe, that is steel pipe with equal side length. It is made of rolled strip steel after process treatment. Steel pipe has been an essential material in building decoration. Galvanized pipe is also used more in decoration, but hot-dip galvanized steel pipe manufacturers need to know about the size of galvanized pipe and several common sizes of galvanized pipe, which is helpful for your purchase!What is the purpose of flat steelAweil,GB No. I-beam is in height, in leg width and in waist thickness.Because all parts of I-beam are arranged at right angles, I-beam has the advantages of strong bending resistance simple construction, cost saving and light structural weight in all directions and has been widely used. The inner and outer sides of the flange of the I-beam are parallel or close to parallel, and the end of the flange is at a right angle, and the flange width is larger than that of ordinary I-beam with the same height of web, so it is also named wide edge I-beam.Under the action of thermal stress, because the initial temperature of the surface layer is lower than that of the heart and the shrinkage is greater than that of the heart, the heart is pulled. At the end of cooling, because the final cooling volume shrinkage of the heart cannot be carried out freely, the surface layer is compressed and the heart is pulled. That is, under the action of thermal stress, the surface of the workpiece is finally compressed and the center is pulled. This phenomenon is affected by factors such as cooling rate, material composition and heat treatment process. The faster the cooling rate, the higher the carbon content and alloy composition, the greater the uneven plastic deformation caused by thermal stress during cooling, and the greater the final residual stress. On the other hand, due to the change of microstructure during heat treatment, i.e. the transformation from austenite to martensite, the increase of specific volume will be accompanied by the expansion of workpiece volume, and each part of workpiece will undergo phase transformation successively, resulting in inconsistent volume growth and structural stress. The final result of the change of tissue stress is the tensile stress on the surface and the compressive stress in the center, which is just opposite to the thermal stress. The microstructure stress is related to the cooling rate, shape and chemical composition of the workpiece in the martensitic transformation zone.

H-section steel is an economic section high-efficiency profile with more optimized section area distribution and more reasonable strength weight ratio. It is named because its section is the same as the English letter 'H'. There is no slope on the inner side of the two outer edges of H-section steel, which is straight. This makes the welding and splicing of H-section steel simpler than I-section steel, and can save a lot of materials and construction time.It is divided into circular welded pipe and special-shaped (square, flat, etc.) welded pipe. The small length of repair welding is mm; The raw material shall not exceed mm after grinding by welding edge.Design brand,What is the purpose of flat steelClassification introductionWhen we carry out different projects, we must use different raw materials, which can ensure the quality of the project. In many kinds of data, alloy pipe is widely used. In many projects, we will apply it, so it is very popular in the field. When people carry out the construction of alloy pipe project, there are many things that must be paid special attention to. Let&#;s take you to know:

H-section steel is an economic section steel with better mechanical properties than I-section steel. It is named because its section shape is the same as the English letter 'H'. The flange of hot rolled H-beam is wider than that of I-beam, with large lateral stiffness and strong bending resistance. Under the same specification,SerikHow much is 28b I-beam per ton, H-beam is lighter than I-beam.Quality recommendation,Whether I-section steel is ordinary or light, due to the relatively high and narrow section size, there is a large difference in the moment of inertia between the two main sleeves of the section. Therefore, it can only be directly used for members bent in the plane of their web or form lattice stress members. It is not suitable for axial compression members or members with bending perpendicular to the web plane, which makes it very limited in the scope of application.The pollution of the joint causes the welding cracking. The composite pipe welding is an accurate work. If it is not done well, it will not only waste resources, but also lead to work efficiency,SerikHow much is 6 points galvanized pipe, rework and restart, and waste financial resources.Alloy pipe is a spiral seam seamless steel pipe, which is made of hot-rolled strip steel coil, often processed by warm extrusion and welded by automatic double wire double side arc welding process. The alloy pipe sends the hot-rolled strip steel to the welded pipe unit,The specification of I-beam is expressed in cm of waist width. For example, expressed as No. ~ No., and the inclination of inner side wall of leg is : The pass system of rolled I-beam includes direct rolling pass system, cross rolling pass system and mixed pass system. In addition, I-beam can also adopt special rolling method.d. All machines and equipment in a production line can connect with the software of the computer data collection system to complete the timely transmission of data information, and the performance parameters in the production process are monitored by the central control room.When selecting I-beam in structural design, reasonable I-beam shall be selected according to its mechanical properties, chemical properties, weldability and structural size.