BurgasCold storage installation worksProblems in using

Large space rate of quick-frozen warehouse: for quick-frozen warehouses of the same size, reasonable design schemes store more goods than unreasonable ones. For the fixed size quick freezing warehouse,BurgasProfessional cold storage installation, how to design it to maximize its space rate is often an important problem considered by our designers. In the design scheme of Lukang medical quick-frozen warehouse, we reasonably designed to expand the original storage capacity of boxes to boxes, which increases the space a lot.Energy saving and power saving: the design cost of quick freezing warehouse mentioned above is very low, but it has a great impact on the cost of quick freezing warehouse and later use cost. The electricity bill is often an important expenditure item in the later stage. The design scheme of the show can greatly reduce the power consumption of the quick freezing warehouse. The selection of the back sunny side of the quick freezing warehouse, the selection of the thickness of the thermal insulation board should be appropriate, the tightness of the quick freezing warehouse door, and the temperature difference between the adjacent cold storage rooms should not be too large are all issues that we need to consider. There are also some tips, such as the use of air curtain machine on the quick freezing warehouse door. We remind users to use parallel units in quick freezing warehouse as far as possible and start them reasonably.Burgas, the speed must be strictly guaranteed during the purchase and shipment of products. If the temperature of the medical cold storage is about degrees, the opening time must be strictly within minutes. If the temperature of the medical cold storage is left and right degrees, the opening time can not be too high, strictly within minutes.Fariskur,Compression refrigerator is commonly used, which is mainly composed of compressor, condenser, throttle valve and evaporation pipe. According to the way of evaporation pipe device, it can be divided into direct cooling and indirect cooling. Direct cooling the evaporation pipe is installed in the refrigerated warehouse. When the liquid coolant passes through the evaporation pipe, it will directly absorb the heat in the warehouse and cool down.Preparation, prepare the project planning of cold storage, and prepare the construction site and construction materials. All kinds of materials for cold storage construction are customized according to the needs of customers. Sort out the construction site that meets the requirements, transport all installation materials to the construction site, check the material quality and model, under the unfavorable local temperature and humidity conditions, the characteristics of the cold storage still do not separate and fall off from the carrier layer and remain stable under normal conditions.

Here we focus on polyurethane. Polyurethane is an ideal cold storage material in the cold storage project. Superior bonding properties make the foam and metal panels form a solid whole,BurgasCold storage of drugs, so that no other adhesive materials are needed. When polyurethane is used as a cold storage project, rigid polyurethane foam is formed between the panels of the storehouse panel, and then solidified and pressed to form a multi shape storeboard, because the metal plate can roll out different waveforms, so that the overall rigidity is stronger and the bearing capacity is higher. Polyurethane filler board can meet the firmness and physical requirements of exterior wall and can be used in various cold storage projects. It is technically feasible and cost-effective. Yuanbao refrigeration believes that polyurethane is one of the new cold storage materials with great development prospects in the future. The thermal insulation materials of cold storage engineering should not only have good thermal insulation performance, applicable and environmental friendly. To ensure the smooth progress of our cold storage project, we should not only inquire about the raw materials of the cold storage, but also the types of cold storage. The common cold storage plates mainly include the following types, namely stainless steel plate, color zinc steel plate, salted steel plate, each contact shall be installed with wire number for maintenance.During installation, the plates shall be handled with care. Rough operation is strictly prohibited. Burrs shall be removed at the cutting opening to prevent scratching the plate surface and workers.reform,Cold storage construction: which one is suitable for you? Which one is suitable for you?During the use of cold storage, attention shall be paid to the collision and scratch of the storage body to avoid the depression and corrosion of the storage plate,BurgasQuotation for cold storage installation, which will seriously reduce the local thermal insulation performance of the storage body.Whether there is dirt on the condenser and poor heat dissipation will lead to too high condensation pressure of the refrigerator. In order to protect the compressor, the machine stops running under the action of the pressure controller. When the heat dissipation is good press the black reset button on the pressure controller, and the goods in and out and operation management are not as convenient as single-layer cold storage; With the development of the floor load capacity and the machine can automatically resume operation.

Disadvantages of multi-layer cold storage: the vertical transportation volume of the warehouse is large, the floor area ratio of each cold room is low; When the multi-storey cold storage is built on the foundation with poor ground resistance, the foundation construction is complex. High cost; When prefabricated components are used, large construction equipment is required and the construction period is long.Management Department,Drainage measures shall be provided for the villa room and overhead layer of the road surface of the cold storage engineering building.If the cold storage is in the building, the load-bearing of the cold storage should be considered. That is, after the fruit is loaded in the cold storage, whether the floor can bear such weight.In order to ensure the safety of construction and cold storage operation, the span between the top storage plate supports (lifting points) shall comply with the following provisions: the polystyrene top storage plate (mm thick) has a very large span of M, and the polyurethane top storage plate (mm thick) has a span of m.Burgas,Cold storage design segmentation: several different partitions shall be reasonably planned and divided according to purpose and temperature. For example: processing room, sorting room, quick freezing room, refrigeration room, channel unloading platform, etc.Feasibility of the design scheme: the design of the quick-frozen warehouse can not be taken for granted. Many restrictive factors should be considered. In practice, a reasonable design scheme should be given according to local conditions. For example, the large-scale quick-frozen warehouse I built for my family should be refrigerated with ammonia in theory because the refrigeration capacity of ammonia refrigeration is large, and I found that it is cheap to replicate cold through actual field investigation.In order to ensure the safety of construction and cold storage operation, the span between the top storage plate supports (lifting points) shall comply with the following provisions: the polystyrene top storage plate (mm thick) has a very large span of M, and the polyurethane top storage plate (mm thick) has a span of m.