Create entry
World Encyclopedia  > category  >  Machinery and industry equipment encyclopedia   

MolfetaDistribution transformer analysisExcellent functionality in the industry

release time: 2023-03-22 14:00:32

When the new oil filled by the power transformer and the oil sample that has just been considered are used,MolfetaPrice of 400KVA dry type transformer, the oil sample can be used only after sufficient standing.The hanging core of dry-type transformer is a vital partMolfeta,The rate of transformer is: n = P / pxo%, that is, when the copper loss of transformer is equivalent to iron loss, the rate is very large. Therefore, the load of transformer is: = P / PK. Fully consider the active power loss caused by reactive power in the system software during transformer operation. The load adjustment is: it can be seen from the calculation of load formula that the large rate of transformer does not occur when the load is full, Generally, it is about %, but when selecting the transformer capacity, we should select effective transformers according to the load condition and load, so as to make the transformer in the situation of economic development and achieve the goal of power saving.What is the wiring mode of dry-type transformer?Khash,The flange surface is uneven, the tightening bolts are loose, so that the bolts are not tightened well, all anchor bolts of the automobile oil tank at the upper end of the detachable oil cover shall be tied with the lifting jack, and the lifting point shall be on the common earrings or bolts. If necessary, the human resources traction belt shall be used as a guide.Oil leakage at looper flange


MolfetaDistribution transformer analysisExcellent functionality in the industry



On load commissioning:Power saving analysis of transformerDue to careless transportation of the transformer and the thin high-voltage conductor, the transformer was disconnected by vibration (but there was no grounding device).Development Curriculum,MolfetaComplete list of Transformer Models,The voltage regulating tap changer is not in place or poorFault judgment of power transformerFor the leakage that has already occurred find the leakage point first, which can not be ignored. For the position with serious leakage, shovel or sharp punch can be selected. The leakage point can be riveted with special tools for metal materials. After manipulating the leakage,MolfetaOil immersed regulator, the goal of long-term treatment of leakage can be achieved.


MolfetaDistribution transformer analysisExcellent functionality in the industry



Solenoid insulation deteriorationRecommendation and consultation,Avoid aging and damage of power transformer iron core insulation: aging of iron core insulation or damage of waterproof sleeve holding anchor bolt will cause large vortex of iron core, and long-term scalding of iron core will lead to insulation aging.The transformer manufacturer said that the selection should be based on the application environment of the dry-type transformer. For the extremely extreme environment, the dry-type transformer should be poured with epoxy resin glue. Because this kind of environment does not need to heat the dry-type transformer, it can operate immediately. However, for the general application environment, the class H dry-type transformer can be used.Oil leakage of cast iron partsMolfeta,Note: in the whole process of safety patrol inspection, the on-site operation and maintenance management staff must use temperature tester or thermal imager to carry out purposeful inspection on the transformer itself, terminal block and other accessories; The sound during the operation of the transformer is a symmetrical current sound. If the sound is found to be abnormal, significantly expanded, or there is local sound, the cause shall be found immediately and certain effective measures shall be taken. If necessary, the load can be reduced or the operation of the transformer can be stopped.In the whole process of transmitting electromagnetic energy in the power supply system, it will inevitably cause the loss of voltage and output power. When transporting the same output power, the voltage loss is inversely proportional to the voltage, and the output power loss is inversely proportional to the square meter of voltage. The transformer is used to increase the voltage and reduce the closing damage.Power transformer

Attachment list


0

The content of the entry is for reference only. If you need to solve a specific problem (especially in the fields of law, medicine, etc.), it is recommended that you consult professionals in the relevant fields.

Synonym

No synonyms