ReinaBaigang deep well pumpWhat if something goes wrong

　　In this way, when the equipment is used again, the solvent in the pump is often less, and the power consumption is also less, and the efficiency of the pump in use is often improved, and the fact is　　 The fan speed of the water pump is too low, and the air pressure and air volume are relatively small so the heat cannot be dissipated.Reina, copper pipes and non-toxic plastic pipes are no longer proposed.　　Second, the power used is not matched, so the motor temperature will be too high after long-term overload operation; In addition, frequent startup during use will also lead to fever, so IBanjo Gore,　　It is located in the middle so it seems that many regions have good effects when using it.　　Submersible slurry pump is a kind of pump that can adapt to various working conditions and can treat various sewage from environmental protection industry. Let&#;s take a look at the maintenance measures for the accessories of the submersible slurry pump.　　First, let&#;s talk about the familiar vertical slurry pumps. Here we refer to ZJL and SP submerged slurry pumps. Strictly speaking, the submersible slurry pump is also a vertical slurry pump because its axis is basically vertical when it works, so it is a good choice

　　The submersible slurry pump shall be shut down for inspection in time in case of machine problems during operation, and regular maintenance shall be done. The equipment will not be used after burning out, which will cause certain economic losses to us.　　 touch method: touch the pump to monitor the changes of temperature, vibration and clearance,ReinaSubmersible pump can pump sewage, so as to judge whether the pump is faulty.　　Head refers to the energy obtained from the pump by the unit weight of liquid output by the pump, so head refers to the effective energy obtained from the liquid output by the pump in unit time - that is, the effective power of the pump: the equation is PE= ρ GQH (W)= γ QH (W)reform,　When using the submersible slurry pump, the equipment may be burned out. The main reason for this phenomenon is improper operation. How should we prevent the burning out?　　Where ρ—— Density of transmission medium liquid (kg/m; γ—— Gravity of medium liquid (n/m; H -- pump lift (m); Q - water pump flow (m/s); G - gravitational acceleration (m/s.　　The difference between the shaft power P and the effective power PE is the power loss in the pump, which is measured by the pump efficiency. The pump efficiency is the ratio of the effective power and the shaft power, which is measured by η Indicates.　　Ordinary vertical motor can be used without waterproof, while the motor shaft and pump shaft of submersible slurry pump are coaxial, so the motor must be waterproof and sealed, and the motor and pump can be immersed in liquid at the same time; The vertical slurry pump is an early product,ReinaCentrifugal slurry pump, and the submersible slurry pump is a newly developed product according to the market demand

　　 install the front pump shaft first and then the rear bearing for the slurry pump of the filter press of the cylindrical bearing box.Honesty is the foundation,　　Avoid airborne sound transmission; Ensure the airtightness of machine room doors and windows. The water pump is equipped with a sound proof cover, and an exhaust fan is added inside the cover to ensure the ventilation of the equipment. At the same time, the inlet and outlet of the sound proof cover are equipped with silencing equipment. A vibration isolation platform is installed at the bottom of the water pump for foundation vibration reduction to isolate the vibration generated during the operation of the water pump　　 whether there is oil　　What is the cause of pump overload.Reina,　　Stop, press down the nut, and fix the axial position of the rotor. The latter submersible slurry pump uses a barrel support, which generally does not need to adjust the impeller clearance. Therefore, if there is a problem with the clearance in the future use, loosen the support clamp first, and say that the nut is loose　　Cavitation of the pump is caused by water evaporation of the pump. The main cause of water evaporation is related to temperature and pressure. Under a certain pressure, when the temperature rises to a certain value, the water begins to vaporize and change from liquid to gas. On the contrary, at a certain temperature, the pressure drops to　　Reasonable.