OfachemDrilling fluid slurry pumpWhat does it do for the current

　　The submersible slurry pump is developed to adapt to the increasingly complex working conditions and facilitate the use of users. Its use mode is more flexible. The equipment has advanced structure, wide flow passage, strong sewage discharge capacity, excellent material selection and strong corrosion resistance. Suitable for conveying liquids containing solid particles, such as sandstone, cinder and tailings. So what are the requirements for its work? Let&#;s understand briefly.　　The purpose is to inject liquid higher than . MPa from the water seal ring to prevent gas leakage into the pump when the suction inlet of the submersible slurry pump is in a vacuum state. When the water pressure in the pump is higher than . MPa, the sealing fluid .-. MPa higher than the pressure in the pump can be injected to seal and reduce leakageOfachem,　　In fact as far as whether the vertical pipeline pump has a suction lift is concerned, we can tell that it has a suction lift. But what you need to know is that suction range and self-priming are actually two different concepts.　　In this way, when the equipment is used again, and the power consumption is also less,OfachemIrrigation deep well pump, and the efficiency of the pump in use is often improved, and the fact isFetesti,　　 A trash trap can be added at the position of the water inlet pipe and used at an angle of degrees, and then a filter screen is installed in the trap to filter impurities for the second time,OfachemZD slurry pump,OfachemDeep well submersible pump, so as to avoid the blockage of the submersible slurry pump during use.　　The slurry pump should be larger. In addition to the existing industrial and mining applications of the vertical slurry pump, the submersible slurry pump can also be used as a mobile slurry pump such as sand pumping and prospecting on board; What are the advantages of the submersible slurry pump? The advantage of the submersible slurry pump is that it is convenient and flexible, easy to operate and submerged　　In recent years, the demand for submersible slurry pumps has increased greatly. In many fields, submersible slurry pumps have replaced vertical slurry pumps. What are the differences between the two? Let&#;s yze.

　　 The rotor assembly is designed according to the actual situation, and the operation is more stable!　　Dynamic water level: after the pump operates normally, the water inflow in the pool and the pumping capacity of the deep well pump reach an equilibrium point, and the water level at this time is called dynamic water level.　　The Tao part also consumes part of it.Where is good, when the submersible slurry pump is blocked during use, it will not only have a certain impact on the working efficiency of the equipment during operation, but also cause serious damage to the equipment itself, so it is also a reminder that we are using it too　　Vertical slurry pump is an early product. Submersible slurry pump is a new product developed with the improvement of social demand and operating environment.　　The Tao part also consumes part of it.

　　Carbon,　　Rate.　　Structural features of horizontal slurry pump: The ah chemical industry and other industrial industries are mainly used to transport abrasive pastes containing solid particles.system, HH and L-type slurry pumps at the pump head are of double pump shell structure, that is, the pump body and cover are equipped with replaceable wear-resistant metal lining, and the flow passage components such as impeller, sheath and guard plate are made of high chromium wear-resistant metal. The pump body and cover are made of grey cast iron according to the working pressure　　It will generate heat, but when it is serious, it will directly burn out the insulation; There may also be some faults in the ventilation system. At this time, it is necessary to check whether the fan of the submersible slurry pump is damaged or rotatingOfachem,　　We also need to limit the starting frequency and select appropriate thermal protection devices for use.　When using the submersible slurry pump, the equipment may be burned out. The main reason for this phenomenon is improper operation. How should we prevent the burning out?　　 The bus voltage where the motor is located is V. Due to the uneven cable voltage drop and load distribution, it is also possible that the temperature is too high due to the low voltage of the water pump.