GiguaniWQ submersible sewage pumpThe right choice is particularly important

　　Moreover, the leaked flammable,GiguaniVertical slurry pump, explosive and toxic liquid will cause fire explosion and poisoning, and the consequences will be unimaginable.　　 When stopping the operation of the submersible slurry pump, and After that cut off the power supply of the motor. If the temperature of the environment is low, open the square plug at the lower part of the pump body to remove the remaining water to avoid frost cracking. During operation, the maximum temperature of the bearing shall not exceed ℃, and the quantity of calcium base grease used for lubricating oil bearing shall be the same as that of the bearing bodyGiguani,　　Easy installation and disassembly.　　Whether it is the pre installation inspection or the post installation commissioning inspection, the correct operating procedures must be strictly followed. Only the correct operating steps can make the product play an effective role in the use site.Calarasi,　　 In addition, the use of ° and S-shaped bends should be reduced as much as possible during the installation and design of pipelines.　　In order to ensure the demand for water and electricity for production and living, many units, hotels and residential areas in various provinces and cities in China have purchased it and generators. Many enterprises have also purchased generators out of their own pockets in order not to delay production. Driven by this, it and the generator naturally become popular　　Submersible slurry pump is a kind of pump used in mines. Do you know the effect and form of its shaft seal? Let&#;s have a look.

　　 Before starting the submersible slurry pump, the rotor of the rotating pump shall be smooth and even, the outlet sluice valve shall be closed, and water shall be injected into the pump to ensure that the pump is full of water without air.　　 the full-automatic control cabinet can be equipped according to the needs of users to automatically protect the water leakage, electric leakage, overload and over temperature of the pump, which improves the safety and reliability of the product.　　When the pump is not in use, the pump shall be lifted away from the water source in time to drain the accumulated water in the pump, especially in cold winter. Then put it in a dry place. Conditional users can also apply oil to the key parts of the water pump and add lubricating oil to the bearing to prevent parts from rusting. in additionindex,GiguaniSplit vertical pipeline pump,　　The motor is scrapped. Moreover, because the length of the long shaft is generally fixed, the installation and use of the pump is troublesome, and the application occasions are subject to many restrictions.　　Wheel, mixing impeller and other main flow passage parts are made of high wear-resistant raw materials, which are wear-resistant, corrosion-resistant, and have strong sewage discharge capacity, and can effectively pass through large solid particles. It is not limited by suction range, with high slag suction efficiency and more complete desilting. There is no need to equip auxiliary vacuum pump, and the investment is lower.　　If there are sundries blocked, the pump will not be filled with water. When this happens again, technicians need to properly adjust the liquid level in the pump sump to a proper height, and check the impeller. In case of damage or aging it needs to be replaced in time, avoiding the phenomenon of burying the pump during use.Fair price,　　; In practical application, the submersible slurry pump is developing rapidly with its unique advantages. The vertical slurry pump needs to be fixed and installed in use, which is convenient and flexible.　　 altitude of pump installation site M　　 add water with manual pump. Some pump owners have their own hand pumps. They can also buy or manufacture their own small hand pumps. The gate valve shall be installed at the water inlet. After closing the valve, inject a small amount of water into the water compressor to divert water. When the hand pump discharges water, it means that the pump is fullGiguani,　　 If there is abnormal sound inside the slurry pump and there is no water, it is likely that the equipment may have air infiltrating into it when absorbing water, which will cause abnormal sound inside the pump, and then at the same time, the impeller is damaged or the impeller is damaged　　After that, the secondary and tertiary pumps can be started successively until the final stage pump. After all the series pumps are started, the outlet valve of the final stage pump can be gradually opened. The speed of opening the valve should be controlled by the fact that the pump does not vibrate and the motor of any stage does not exceed the rated current.　　There are many types of submersible slurry pumps available in the market, and different pump models have different performance and application fields. Therefore, although the pump has a wide range of applications, if its model is not correctly and reasonably selected, its application effect will be great