TaborBooster pipeline pumpTips for using

　　The submersible slurry pump is a slurry pump which is connected with the motor and works under the water at the same time. Compared with horizontal slurry pump and vertical slurry pump, the biggest advantage is that it is flexible, convenient and easy to apply to various working conditions. The most important technical point of submersible slurry pump is the tightness between its motor and pump body Stability and reliability of seals.　　 one method is to use ultrasonic method to detect whether the equipment has cavitation. This method is often convenient for re detection. Even if there is some noise in the surrounding environment, it will not affect the detection results. Therefore, many pumps tend to have better measurement results when in use.Tabor,　　 The fire control cabinet has fault alarm . When a single fire pump is working, it is not easy to be found in time in case of insufficient water source, power circuit failure, resulting in damage to the fire pump. Using the fire control cabinet, the alarm of the control cabinet can remind each　　 one method is to use ultrasonic method to detect whether the equipment has cavitation. This method is often convenient for re detection. Even if there is some noise in the surrounding environment, many pumps tend to have better measurement results when in use.Nyaunglebin,TaborFire deep well pump,　　 Inspection before installation: Check the specification, size and quality of thick and thin accessories.　　 In addition, the noise method directly detects the noise of the equipment in the detection process, but this measurement will also be affected by the surrounding noise, so in fact, this measurement is not very accurate.　　The water pump can be used to transport and pressurize clean water without impurities such as apartment, villa water supply residence,TaborBooster pipeline pump, factory water supply, water supply system, drinking water system and water treatment. In short, there are many uses.

　　 confirm whether the pressure capacity of the pipeline meets the requirements, voltage and outlet pressure every day, check the dynamic water level every two weeks and make records.　　Function of shaft seal of submersible slurry pump: the main of shaft seal is to prevent high-pressure liquid from leaking out of the pump and prevent air from entering the pump.Discount,　　There is no need to equip auxiliary mixing or spraying equipment, and the operation is simpler. The equipment is directly submerged for operation, without noise and vibration, and the site is cleaner.　　Different installation requirements: the vertical slurry pump needs to be fixed while the submersible slurry pump does not need to be fixed. It can directly invade into the liquid for operation.　　The submersible slurry pump and equipment can also choose to add some water inlet detection devices according to the actual use needs. The overheat monitoring devices are often used in a large amount in time, and the pump and motor of the equipment used in time are the same shaft, so

　　The whole packing body, including the packing gland, packing ring and packing, needs to be disassembled; Submersible slurry pump Disassemble the o-seal ring, shaft sleeve, balance disc and key on the shaft in turn, and then the discharge section includes the last stage guide vanereform,　　 Structural features and working principle qsz submersible slurry pump is a coaxial integration of water pump and motor. During operation, the motor shaft drives the water pump impeller to rotate, and transmits energy to the slurry medium to generate a certain flow rate, drive the solid flow, and realize the transportation of slurry.　　It is worth noting that the QW mobile type is generally used without a fixed position, so it is usually used temporarily without an electric control cabinet, and a special person is required to control the shutdown of the water pump.　　Stop,TaborSubmersible non clogging slurry pump, then tighten the bearing seat, press down the nut, and fix the axial position of the rotor. The latter submersible slurry pump uses a barrel support, if there is a problem with the clearance in the future use, loosen the support clamp first, and say that the nut is looseTabor,　　 When the slurry pump fails to absorb water during operation, it may also be because the bottom valve is not opened. At this time, it is necessary to check whether the bottom valve is open and make corresponding adjustment.　　There is a difference between submersible slurry pump and sewage pump. Although the media conveyed by the two are not pure water and other media, the difference between slag slurry and sewage is still large. Let&#;s take a look at the difference between the two.　　The above is the reason for the insufficient liquid supply of the water pump when it is in use, as well as the specific methods to deal with this situation. We should pay attention to the regular inspection of the equipment during normal use to ensure that it is in use