DeruskinkaVertical heavy-duty slurry pumpProduct trends and emerging categories

　　 the submersible slag pump is often used to transport pulp containing solid particles, so the wear resistance of the pipeline should also be considered.　　Start the priming pump. Moreover, due to the structural limitations of the submersible slurry pump, the motor needs to be placed on the water surface for use during operation,DeruskinkaBooster pipeline pump, and then the pump needs to be placed in the water for use. Therefore, the submersible slurry pump must beDeruskinka,　　 When the electric pump is not in use, take it out of the water and do not immerse it in the water for a long time, so as to reduce the chance of the motor stator winding getting damp and increase the service life of the electric pump. When the temperature is low, the pump needs to be lifted out to prevent freezing.　　 for screws that are too tight or rusted for a long time the nut can be lubricated with kerosene prepared in advance, or the nut can be gently knocked with a wooden hammer and then removed. This method can also be used in slurry pumps and other places.Denpasar,　　Compared with the vertical slurry pump the application market is also larger. In addition to the existing industrial and mining applications of the vertical slurry pump, the submersible slurry pump can also be used as a mobile slurry pump, such as sand pumping on board, prospecting, the cost has been reduced,DeruskinkaPipeline pump, when the load conditions do not match the model of the slurry pump, for example, the pump lift used is too high or too low, which will lead to overload, so we are selecting the pump

　　Pressure. Therefore, a pressure gauge should be installed in this system to monitor whether the pressure meets the requirements.　　Operation, maintenance and upkeep During the operation of the electric pump always observe the current, voltmeter and water flow and strive to make the electric pump operate under the rated working condition.　　Stability and reliability of seals between pump bodies.Customer first,　　Different installation requirements: the vertical slurry pump needs to be fixed, while the submersible slurry pump does not need to be fixed. It can directly invade into the liquid for operation.　　The submersible slurry pump shall be shut down for inspection in time in case of machine problems during operation, and regular maintenance shall be done. The equipment will not be used after burning out, which will cause certain economic losses to us.　　The seal cannot bear the water pressure at this depth. Once the water leaks, the motor will not work normally, resulting in damage to the submersible slurry pump. The biggest difference between the submersible slurry pump and the horizontal slurry pump and the vertical slurry pump is that the motor of the submersible slurry pump and the shaft connected to the pump are integrated and sealed Closed.

　　 We must choose to consider the actual use situation when making the selection, because there will be some difference between the marked head when using and the head when using. This is because the pipe itselfproduction,　　Some corrosive pastes containing crystals can also be transported. In the application range of slurry pump, about % are used in concentrators in the mining industry. Due to the poor working conditions of primary ore dressing,DeruskinkaZD slurry pump, the service life of slurry pump in this section is generally low. Of course, different minerals, abrasion　　It is about % of the solid particles of the pump diameter. It has the characteristics of remarkable energy-saving effect, anti winding, non blocking, automatic installation and automatic control. It has a unique effect in discharging solid particles and long fiber waste. Very suitable for chemical, petroleum, pharmaceutical, mining, paper industry, hydraulic and other professions; The mechanical seal is tight and reliable, and the leakage probability does not exceed drops /min, which is mostly used to transport flammable, explosive, toxic, strong corrosive and valuable liquids or materials with high temperature, high pressure and low temperature.Deruskinka,　　Auxiliary mixing or spraying device shall be equipped for easier operation. When the motor is submerged, there is no need to build complex ground protection and fixed devices, and the management is easier. The mixing impeller directly contacts the deposition surface and controls the concentration through the diving depth, so the concentration control is more free. Equipment directly submerged　　The above four methods can be used to detect whether the submersible slurry pump has cavitation, because if the equipment is in use, it will have a great impact on the operating efficiency. Even if the cavitation time is long, it will also have a certain impact on other parts of the equipment. Sometimes submersible slurry pump　　So it has a process of water diversion and exhaust. There are usually two ways to inject water into equipment. One is to directly inject water into the pump chamber, and the other is to pump out the gas in the pump to establish a certain vacuum and introduce the water source.