Novi Pazar Fruit preservation cabinet coldStrong compilation ability

No matter whether the food cold storage or quick-frozen storage is in use, it is inevitable that there will be various small faults. Don't be nervous when there are problems. You can find or eliminate problems according to the knowledge taught today.The polyurethane insulation board shall be connected by plug-in notch connection, because it has higher strength when connecting in this way.Novi Pazar ,The circuit system must be -wire system. If there is no ground wire, the ground wire shall be added.Fire retardant, flame retardant and high temperature resistant polyurethane is a kind of flame retardant self extinguishing material after adding flame retardant. Its softening point can reach more than ℃, polyurethane forms carbon deposits on the surface of the foam, which helps to isolate the foam below. It can effectively prevent flame spread.Banora Point,Novi Pazar Vegetable fresh storage company,Core tip: in the cold storage project, only with sufficient cold storage installation skills can we ensure that the cold storage is more energy-saving and power-saving after installation, and is not prone to failure, convenient use and management and long service life.Panel types of quick freezing warehouse: color plastic steel plate, salted steel plate, stainless steel plate, embossed aluminum etc.Technical assurance measures for the installation of cold storage: during production in the production workshop, the production shall be carried out in strict accordance with the operation rules specified in ISO quality operation, self inspection and inspection application shall be carried out to ensure that the factory pass rate is, and unqualified products are not allowed to leave the factory.

However, long-term continuous operation will inevitably lead to equipment aging, so reasonable maintenance is particularly important.The volume of cold storage the size of cold storage shall be calculated according to the volume occupied by the stacking of goods stored in the cold storage plus the corridor from row to row, the indoor space between the stack and the wall, and the gap between the ceiling and the packaging room. After determining the volume, the length width ratio of the cold storage shall be determined. When designing the cold storage, necessary auxiliary engineering buildings and equipment should also be considered, such as working intermediate, packaging and combing room, special tool warehouse and loading and unloading platform, so as to ensure the quality of the cold storage. - floor installation of cold storage: first level the floor, then install the floor, select a beautiful floor and put it in a conspicuous place, and do a good job in the floor and evaporator drainage system.Safety and health,The closed cell structure and surface material of polyurethane rigid foam with good moisture-proof, waterproof and corrosion resistance make it have better air resistance and water vapor resistance, and it can be made into inlaid connection structure during forming, it will not only increase the cold consumption of the cold storage, but also bring water into the warehouse. The condensation of water will lead to the building structure, especially the heat insulation structure, being damaged by moisture and freezing. Therefore, a moisture-proof and heat insulation layer should be set to keep the cold storage board building moisture-proof and air-proof performance and good sealing.The selection of equipment for the construction of equipment cold storage is closely related to the size, type and budget of the cold storage.

Requirements for refrigeration equipment in quick freezing warehouse: the strict sealing of quick freezing warehouse is obviously different from that of ordinary quick freezing warehouse. Therefore,Novi Pazar Pharmaceutical refrigeration equipment, how to seal the refrigeration equipment is the key. First of all, all through wall pipelines must be equipped with sleeves, the frost flushing water return pipeline must be equipped with U-shaped bend water seal and the main frost flushing and return pipeline outside the warehouse shall be equipped with air filling port to prevent the gas in the warehouse from being pumped out of the warehouse by negative pressure. In addition, due to the good sealing of the quick freezing warehouse, the set fluctuation range of the warehouse temperature should not be too large to prevent excessive positive and negative pressure from damaging the warehouse body.knowledge,Whether there is dirt on the condenser and poor heat dissipation will lead to too high condensation pressure of the refrigerator. In order to protect the compressor, the machine stops running under the action of the pressure controller. When the heat dissipation is good, press the black reset button on the pressure controller, and the machine can automatically resume operation.The exhaust temperature of fresh-keeping storehouse is directly proportional to the compression ratio and suction temperature. If the suction superheat temperature of the fresh-keeping warehouse is high and the compression ratio is large, the exhaust temperature is also high. If the suction pressure and temperature remain unchanged, when the exhaust pressure increases, the exhaust temperature also increases.Floor insulation of small cold storage the structure of small cold storage is usually called surface, that is, the top, wall and ground are made of color steel plate / stainless steel with appropriate thickness of polyurethane and other insulation materials, because the loading and unloading of small cold storage is often handled manually rather than forklift. Of course, if the height of the warehouse is high and the forklift is required for warehousing, loading and unloading, the insulation board is not recommended for ground insulation, but the ground needs to be insulated separately like the ground insulation sample of medium-sized cold storage.Novi Pazar ,Floor insulation of small cold storage the structure of small cold storage is usually called surface, that is, the top wall and ground are made of color steel plate / stainless steel with appropriate thickness of polyurethane and other insulation materials, because the loading and unloading of small cold storage is often handled manually rather than forklift. Of course, loading and unloading,Novi Pazar How much is the installation of vegetable cold storage, the insulation board is not recommended for ground insulation, but the ground needs to be insulated separately like the ground insulation sample of medium-sized cold storage.Insufficient refrigeration dose and capacity in the system: there are two main reasons for insufficient refrigerant circulation,Suggestions on the quantity of polyurethane cold storage insulation materials: cold storage investment is a long-term and profitable investment. A high quantity of hair can certainly reduce the initial investment, because the insulation effect of polyurethane cold storage insulation materials has a parabolic linear correlation with its bulk weight; A large number of studies have shown that the foam bulk density has better thermal insulation performance at ~ kg / cubic meter. Therefore, it is usually recommended that the number of thermostat refrigeratory outlets should be ~ square / ton.