WarwickDouble fork hydraulic lifting platformHow can we achieve double qualitative change

What are the advantages of installing a guide rail type elevator for goods? The advantages of civil engineering are easy to install: there is no need for a machine room above the shaft, and the top layer can be installed at a height of more than meters. The computer room can be located within a radius of meters of the shaft, occupying an area of only - square meters. The hydraulic elevator is not equipped with a counterweight device to improve the utilization rate of the shaft area. The load and load cylinder of the hydraulic elevator directly act on the foundation pit, and the strength requirement for the shaft is low. A brick structure or brick concrete structure shaft is sufficient.Preparation before folding and installation of the elevator. Carefully prepare a special construction plan for installation and provide safety technical disclosure to the installation personnel.Warwick,During the use of hydraulic elevators, if not properly operated,WarwickLifting hydraulic platform, there will always be problems. Many customers have reported that hydraulic elevators sometimes cannot be lifted. If the hydraulic lift pump can continue to work, other issues need to be considered. Below, as well as the solutions for mobile elevators The analysis of the pump station of hydraulic elevators such as guide rail elevators is as follows: the motor power supply is abnormal or reversed; The solution is to correctly connect the motor power supply or adjust the steering mailbox to ensure there is no hydraulic oil or insufficient oil; The solution is to add hydraulic oil.Novice operators: Due to their lack of understanding or lack of understanding of the operation methods of high-altitude work platforms such as mobile elevators, it is easy for them to make mistakes and cause equipment malfunctions. Operators in this area need to patiently learn and pass training before they can operate and use them.Sakete,Once the freight elevator malfunctions, the maintenance unit shall arrive at the site within the specified time (the specific time is not specified in Beijing, but within minutes).There are problems with the hydraulic torque converter and compensation system of mobile elevators, such as weak torque converter, power shift failure, high oil temperature, insufficient hydraulic torque converter, inadequate pressure adjustment, insufficient back pressure. Check the quality of torque converter oil (whether hydraulic transmission oil is misused), dosage, torque converter pressure regulating valve, back pressure valve and their set pressure value. Power shift failure. Quick return valve, pressure reducing valve, power transmission valve The directional valve is stuck or leaking internally. Oil pollution is severe. Check the cause of the valve sticking and eliminate it accordingly. Filter or replace the hydraulic oil. If the oil temperature rises too much, check if there is any problem with the cooler. Check the quality of the hydraulic oil. The brand hydraulic boarding bridge, also known as the hydraulic loading and unloading platform, can achieve rapid loading and unloading of goods. The structure design is simple, the use is flexible and convenient, and the work efficiency is high. It is widely used and widely popularized in the market.When working in a hot environment, pay attention to heat dissipation.

The explanation mainly focuses on the mechanism of lifting platforms and now there are many different types of lifting platforms. In order to better use lifting platforms, we have started to develop different industries using different lifting platforms. Electric lifting platforms have become the main product of small lifting platforms. They are small in size, light in weight, easy to move, stable and free in lifting, large in load capacity, and large in plane area, Stability has become a machinery that many customers are competing for, and lifting equipment is used in enterprises of all sizes, so the use of lifting platforms is necessary.When the motor connection of the elevator is incorrect, when a coil, coil group, or one phase winding group is connected in reverse, it can cause serious three-phase current imbalance and cause the winding to overheat.Familiarity with the usage process and without a doubt, this is the first thing to understand. There are two ways to understand it: first, carefully read the user manual provided by the manufacturer when the hydraulic lifting platform leaves the factory; The second is the equipment that needs to be installed. A professional installation technician will be dispatched to install the hydraulic lifting platform. After the installation is completed, relevant users will be trained on the operating process and safety precautions of the hydraulic lifting platform, and some maintenance matters in the future will also be explained; What should be paid attention to during the running-in period when using hydraulic lifting platforms? Check the wear of components. For newly processed and assembled components, there may be subtle deviations in shape and size that require a period of time for running-in. Therefore, during the running-in period, it is necessary to pay attention to whether there is any rapid wear. If there is any, the manufacturer of the hydraulic lifting platform should handle it in a timely manner to avoid equipment failure; Work between the pins and bearings to ensure that they are not worn, and add some engine oil or grease appropriately; Confirm if there is any noise during the running-in period. If it is found that the hydraulic lifting platform is noisy during operation, run it several times more. After the running-in, the noise will naturally disappear. However,WarwickLifting platform hydraulic pressure, if there is noise for a long time and no signs of fading, please make sure to promptly produce it and solve the problem; Regularly check if the components are loose. Before use, check if there are any signs of looseness in screws, nuts, retaining rings, oil pipe joints,Novice operators: Due to their lack of understanding or lack of understanding of the operation methods of high-altitude work platforms such as mobile elevators, it is easy for them to make mistakes and cause equipment malfunctions. Operators in this area need to patiently learn and pass training before they can operate and use them.The lifting platform has been inspected and debugged before leaving the factory and all technical indicators meet the design requirements. When in use, only the power supply needs to be connected, and the hydraulic and electrical systems basically do not need to be adjusted.When working at heights exceeding . meters, safety nets or safety belts must be used. Specializing in scissor lift manufacturers, old brand, with price advantages and guaranteed quality!

The concept of hydraulic boarding bridge is the power system of the boarding bridge. The large oil cylinder lifts the entire equipment inclined plate. When it is raised to a large height, the small oil cylinder begins to operate, extending the hinge tongue plate. All equipment plates are made of high-quality high height patterned steel plates and profiles, which are effectively welded and have a long service life.Latest quotation,What are the common faults of hydraulic lifting platforms? The hydraulic lifting platform's oil cylinder is severely damaged, and uneven damage to the inner sealing ring or obstacles inside can easily cause uneven stress, resulting in uneven lifting height of the oil cylinder. It is recommended to carefully check whether the oil cylinder is normal.Now we have an increasing demand for cargo elevators. Let me introduce the maintenance work of guide rail cargo elevators to you. When we use a guide rail elevator in our daily life, we need to regularly inspect, maintain, and maintain it. This not only extends the service life of the guide rail elevator, but also makes it more powerful when working! For example, the transmission part should have sufficient oil, and vulnerable parts must be regularly inspected, repaired, or replaced. Mechanical bolts, especially parts that frequently vibrate such as slewing bearings and lifting arm connecting bolts, should be checked for looseness. If there is looseness, it must be tightened or replaced immediately. Below is an introduction to the steps of maintenance: important maintenance work for guide rail elevators. Regularly check the tire pressure and bearing condition of the guide rail elevators to ensure they are in good condition; Regularly check whether the structure of the bracket and panel is in good condition, and add oil and grease to the bearings and components in a timely manner, once a month; Vulnerable parts must be regularly inspected, repaired, or replaced. Parts that frequently vibrate, such as bolts and slewing bearings, should be checked for looseness. If there is looseness, it must be tightened or replaced immediately.What should I pay attention to when starting a new mobile elevator? High priced and various specifications of scissor lift manufacturers welcome scrap merchants, industrial companies, enterprises, and power departments to visit and negotiate with the company!Warwick,The daily maintenance of guide rail type lifting equipment should pay attention to regular inspection and maintenance, eliminate hidden dangers, eliminate faults, and achieve these benefits for improving work efficiency extending equipment service life, and ensuring the safety performance of the elevator.Remove and disassemble the lowering valve,WarwickGuide rail hydraulic lifting platform, blow the valve core clean with compressed air, and then reinstall it.What are the pressures on lifting platforms? The movement of lifting platforms has always been a concern for us. Our usage scenarios are uncertain and most of them are part-time workers. Therefore, we are constantly researching mobile lifting platforms to meet different needs. However in order to better attract customers, we are still accustomed to using fixed elevators, He has a huge load capacity and strong stability, which can meet the needs of many customers, which is also the use of lifting platforms in China in recent years.