PalangaLong shaft submerged slurry pumpExcellent quality

　　Ordinary vertical motor can be used without waterproof, while the motor shaft and pump shaft of submersible slurry pump are coaxial, so the motor must be waterproof and sealed, and the motor and pump can be immersed in liquid at the same time; The vertical slurry pump is an early product, and the submersible slurry pump is a newly developed product according to the market demand　　Therefore, when the pump temperature is too high you don&#;t need to panic. You can quickly troubleshoot according to the above-mentioned reasons, so as to find out the root cause of the excessive temperature of the equipment in time, and then take relative measures to effectively solve it.Palanga,　　 The valve shall be used to regulate the flow and head, and overload operation is not allowed.　　 If it is found that the impeller is damaged and the liquid supply is insufficient,　　 It may also be because the pump&#;s liquid supply pipe is blocked by other substances during normal use.　　It can also be used for cooling and lubrication. Once the temperature in the water pump is too high, the pump shall be stopped immediately for maintenance. Otherwise, the excessive temperature will not only affect the wear of small parts inside the equipment, water will also vaporize, which is called the vaporization pressure of water at this temperature.　　Slide evenly and slowly along the guide rail until the active coupling is in place. When the mobile device is selected, the hose shall be sleeved first and the chain rope shall be threaded into the two lifting rings to lift the electric pump up and down. Be careful not to use the cable as a rope to avoid danger.　　Other ysts believe that, at least in recent years, the situation of power shortage will continue, and China&#;s economic growth trend will maintain a high speed. Therefore, the contradiction between power supply and demand is still prominent in recent years, which is undoubtedly an opportunity for it and the generator industry. In water pumps and generators, especiallyLet's see,PalangaCirculating hot water pipeline pump,　　Head refers to the energy obtained from the pump by the unit weight of liquid output by the pump, so head refers to the effective energy obtained from the liquid output by the pump in unit time - that is, the effective power of the pump: the equation is PE= ρ GQH (W)= γ QH (W)　　In addition the sundries inside the pump body and impeller shall be cleaned. Then calibrate the pump shaft and motor shaft of the slurry pump to make them on the same horizontal line.　　 strip the outer layer of the cable to expose the copper wire for to mm,PalangaQuotation slurry pump, gradually thin the rubber near the wire core, grind it to the oxide layer on the wire core, wipe the wire core with alcohol (or hydrochloric acid), wrap the insulation layer and sheath layer, and dry it naturally.

　　Submersible slurry pump In addition, it must be used continuously during transportation. If there is an interval in the middle, it must be avoided that the interval is relatively long, so as to avoid the solidification of slurry in the pump when the operation is stopped.Service first,　　Head refers to the energy obtained from the pump by the unit weight of liquid output by the pump, so head refers to the effective energy obtained from the liquid output by the pump in unit time - that is, the effective power of the pump: the equation is PE= ρ GQH (W)= γ QH (W)　　 before starting, check all circuits and switches to see if their wiring is correct and reliable, then turn them over the ground for ~ minutes (the time should not be too long to avoid damaging parts or burning motor windings), and check whether the motor running direction is correct. If the above problems are not found, it can be started　　The solution to the excessive temperature of the water pump: when selecting the motor,PalangaAh slurry pump, it is necessary to select one that matches its power and speed. In addition, the cooling fan should be installed on the main shaft. It is also possible to appropriately increase the number of fan blades, but pay attention to adjusting the vacuum pumpPalanga,　　 repair and level the welding part of the submersible slurry pump with a file, but when it is serious, it will directly burn out the insulation; There may also be some faults in the ventilation system. At this time, it is necessary to check whether the fan of the submersible slurry pump is damaged or rotating　　 First remove the pump from the engine.