BallinaFixed lifting cargo elevatorWhat is the national standard quality of

Pay attention to check whether there are any broken wires and loose strands in the wire ropes of each part. If it exceeds the relevant regulations, it must be replaced immediately. The maintenance of the wire rope should be strictly in accordance with regulations.It is strictly forbidden to switch the electric control switch with wet hands. Many people tend to ignore this detail. Although the safety voltage of the hydraulic lifting platform is below V, if you touch the power supply with your hands, it may cause lifting failure in light cases, or electric shock accidents in severe cases.Ballina,Elevators are now widely used and are involved in many industries. The screw jack is no exception, and it has a very good effect. But sometimes the surface of the screw jack will be rusted, which will have a certain impact on the work efficiency and needs to be removed. So is there any way to solve the rust on the surface of the screw jack?Before the elevator manufacturer connects the motor to the elevator, please make the keyway of the motor shaft perpendicular to the tightening bolt. In order to ensure uniform force, but do not tighten them tightly, then screw on the other two mounting bolts at diagonal positions, and then tighten the four mounting bolts one by one. Finally, tighten the tension bolts. All tightening bolts need a torque wrench to fix according to the marked fixed torque data and check whether the lift and lifting platform are used.How should we check the construction site of the construction hoist? you know?Eden,Avoid working in an environment. In the event of rain, snow and other weather, the use of the hydraulic lifting platform should be stopped to prevent the occurrence of a short circuit, resulting in electric leakage and electric shock; non-professionals are strictly prohibited from disassembling electrical appliances such as hydraulic lifting platforms. In the event of an accident, you can’t disassemble without permission to eliminate the cause. You must report to the manufacturer for repair in time, inform the phenomenon of the accident,BallinaElevating cargo elevator, and the manufacturer will guide you to complete the inspection or send someone to repair it; do not disassemble the appliance without permission! Professional elevator factory guarantees quality, guarantees service. Guarantees quality. Your satisfaction is our pursuit! Welcome to inquire.Correct construction elevator site inspection First of all, we need to check the foundation to see if there is any water accumulation, and check whether the grounding system meets the requirements. We also need to check how the structural bolts of the frame are fastened and whether there are any cracks in the welds. We need to follow the instructions to set it up. In mechanical transmission, it can be divided into two types: open type and closed type. Of course the lift also has a lot of safety equipment.After the goods are transported, clean up the debris on the platform.

The safety device of the guide rail hydraulic lifting platform The mechanical part of the guide rail hydraulic lifting platform mainly includes the hydraulic system and the mechanical device.For this reason,BallinaTwo ton lifting cargo elevator, various protective devices are installed on many mobile lifts to ensure the safety of people's lives. Let's take a look at what safety tools are on the mobile lift?Hydraulic pump station: special pump station for domestic lifting platform protection device outside the pump station imported from Italy: organ m type, mesh type,BallinaNew fixed lifting cargo elevator,Safety performance: The lifting structure is made of high-strength manganese steel rectangular tube, with strong stability and high carrying capacity. The maximum lifting height is about meters, and the maximum load is about tons. .The parts such as reduction box, gearbox, external gear and hydraulic oil are all in accordance with the requirements in the table.Conscientiously write the special construction plan for installation and construction, and make safety technical disclosures to the installers.

This kind of fixed lifting equipment can also be used in the warehouse. For example, a certain floor in the warehouse needs to be lifted to send goods or personnel into the designated warehouse.High value,If the motor of the hydraulic lift is overheated, stop the machine in time and continue running after troubleshooting. The motor bearings must be in good condition.Working at heights is a very common thing nowadays, but working at heights also has a certain risk factor. So people invented the hydraulic lifting platform to help people complete high-altitude operations more conveniently. However, people should also pay attention when using the hydraulic lifting platform, otherwise it is easy to fail, which may cause serious consequences. So what are the common faults of hydraulic lifting platforms?Correct construction elevator site inspection First of all, we need to check the foundation to see if there is any water accumulation, and check whether the grounding system meets the requirements. We also need to check how the structural bolts of the frame are fastened and whether there are any cracks in the welds. We need to follow the instructions to set it up. In mechanical transmission, it can be divided into two types: open type and closed type. Of course the lift also has a lot of safety equipment.Ballina,Regarding the cleanliness of the hydraulic station, is there any relevant rule requirement?Conscientiously write the special construction plan for installation and construction, and make safety technical disclosures to the installers.After the goods are transported, clean up the debris on the platform.