GrenobleThree ton cargo elevatorWhat are the key points of the control method

In addition, during installation,GrenobleSimple track lifting cargo elevator, it is strictly forbidden to use hammers, etc. to prevent damage to bearings or gears due to excessive axial force or radial force. Be sure to tighten the mounting bolts before tightening the force bolts. Before installation, clean the anti-rust oil on the motor input shaft, the positioning boss and the connection parts of the elevator with gasoline or zinc and sodium water. Its purpose is to ensure the tightness of the connection and the flexibility of operation, and to prevent unnecessary wear and tear.System: explosion-proof electronic control system, remote control system, P IC system.Grenoble,Make sure to add butter twice a month to the general transmission position where the grease fitting is located. For the parts that cannot be filled with butter, be sure to dredge the oil circuit or replace the grease fitting until the butter can be added,GrenobleFloor to floor cargo elevator, otherwise it is forbidden to use the equipment.After the goods are transported, clean up the debris on the platform.Ferrara, containers, mold manufacturing, wood processing, chemical filling, etc., to meet the lifting needs of different operating heights, and can be equipped with various table forms (such as balls, rollers Turntable, steering, tilting, telescopic), with various methods (separate, linkage, explosion-proof), with the characteristics of stable and accurate lifting, frequent starting, large load capacity, etc., effectively solving the difficulties of various lifting operations in industrial enterprises, so that Production operations freely. The professional elevator factory has advanced technology strict testing, more affordable prices, and more discounts are in progress, welcome to consult.Naturally connect the motor to the lift. When connecting, it must be ensured that the concentricity of the output shaft of the elevator is consistent with that of the input shaft of the motor, it will cause the motor shaft to break or the elevator gear to wear.The anti-rust work of the aerial work vehicle generally needs to be paid attention to when the aerial work vehicle has not been used for a long time. How should we do anti-corrosion for the body of the aerial work vehicle? This is actually very simple. You don’t need to spend money to go to the repair station for anti-corrosion. As long as our car owners use some materials that they can find at hand, it can be realized. At the same time, paying attention to driving habits can ensure that the aerial work vehicle does not rust. Here are a few points that can be used as a reference.

Naturally connect the motor to the lift. When connecting, it must be ensured that the concentricity of the output shaft of the elevator is consistent with that of the input shaft of the motor, and that the outer flanges of the two are parallel. If the concentricity is inconsistent, it will cause the motor shaft to break or the elevator gear to wear.The inconsistency in the production size of the support rods of the hydraulic lifting platform is a quality defect of the lifting platform equipment itself. It is recommended that the manufacturer replace it. The probability of this situation is low.The use of the hydraulic lifting platform The user can choose the power mode and configuration according to his own scope of use: the power system includes: DC power supply, single-phase or three-phase power supply and diesel engine.Click to view,Ensure good power supply at the installation site, install a separate distribution box, and the leakage switch must meet the requirements for construction elevators when used in the distribution box. If the construction elevator installed is frequency conversion, the leakage switch should be adapted to the frequency converter when selecting the leakage switch .Goods should be stacked on the platform and not tilted. When the freight elevator goes up and down beyond the range of the platform, no one should stand around to watch.The design of the hydraulic lifting platform is unreasonable. When the designer designs the cylinder barrel and rod, if there is a problem with the design size and angle, then there will definitely be problems in the later stage. Therefore, it is necessary to confirm the technical strength of the manufacturer when working on a hydraulic lifting platform; what is the problem with the sound of the oil cylinder of the hydraulic lifting platform? Design drawings to make, the angle of the oil cylinder is slightly deviated, it will cause the friction between the cylinder barrel and the rod, which will cause the sound; the seal quality of the hydraulic lifting platform is different, and the use of different seals will also affect the sound of the oil cylinder, and the seal with excellent material The continuous friction between the parts and the cylinder wall will cause the sound to be very loud, and long-term wear and tear may scratch the oil cylinder and cause oil leakage, so when the hydraulic lifting platform is used, pay attention to ask the manufacturer what brand and material the seal is used; In some cases of mechanical running-in, it is not ruled out that the above three situations are normal, and there will still be noises. If there is no problem after investigation, then don’t worry. It’s just a running-in problem between mechanical parts. It will disappear naturally.

In addition, during installation, it is strictly forbidden to use hammers, etc. to prevent damage to bearings or gears due to excessive axial force or radial force. Be sure to tighten the mounting bolts before tightening the force bolts. Before installation, clean the anti-rust oil on the motor input shaft, the positioning boss and the connection parts of the elevator with gasoline or zinc and sodium water. Its purpose is to ensure the tightness of the connection and the flexibility of operation, and to prevent unnecessary wear and tear.Latest quotation,Regarding the cleanliness of the hydraulic station, is there any relevant rule requirement?Familiar with the use process and there is no doubt that this is the first to bear the brunt. There are two ways to understand the content that needs to be understood: one is the instruction manual provided by the manufacturer when the hydraulic lifting platform leaves the factory, which needs to be read carefully; the other is the equipment to be installed, hydraulic The lifting platform will send a professional installer to install it, and some matters for future maintenance will also be explained; the running-in period of the hydraulic lifting platform What items should be paid attention to Check the wear of parts Newly processed and assembled parts have subtle deviations in shape and size and need a period of running-in. During the running-in period the relevant users will be trained on the operation process and safety precautions of the hydraulic lifting platform, attention needs to be paid to whether there is excessive wear and tear. High prices and various specifications Freight elevator factory has timely supply and high cost performance. It has become the preferred brand of many wire products. Welcome to buy! If you haveThe manufacturer handles it to avoid equipment failure; work between the pins and bearings to ensure that, to avoid wear, you can add some oil or butter; confirm whether there is noise. During the running-in period, it is found that the hydraulic lifting platform has noise during operation You don’t have to worry about it in the early stage. If there is no major problem, run it a few more times. After running in, the noise will naturally disappear. But if there is noise for a long time and there is no sign of fading,GrenobleProfessional production of cargo elevators, please be sure to solve it by the manufacturer in time; check the parts regularly Check whether it is loose before use, whether there are any signs of looseness in the screws, nuts, retaining springs, backstops, oil pipe joints, please reinforce or replace it in time to avoid accidents.Goods should be stacked on the platform and not tilted. When the freight elevator goes up and down beyond the range of the platform, no one should stand around to watch.Grenoble, without leakage the switch box also has leakage protection equipment. Its wires and cables are well insulated, and the metal threaded is not rusted, and its damage is close to zero. His steel wire rope should comply with the corresponding configuration requirements and there is no problem of broken strands and diameter reduction. Of course, the number of broken wires should not exceed the corresponding standard. His pulley movement is very flexible.The common types of lifts are simply introduced here for you. I hope you can learn more about this product. At present, because many places need to use this product. Products that can be lifted and moved flexibly at the same time. Now companies that specialize in the production of this product combine a large-scale external publicity on the Internet. Friends in need can directly find the corresponding company on the Internet, and then simply learn about the models of these products and Information on performance and price can be purchased directly through the Internet.In the construction elevator, the switch box also has leakage protection equipment. Its wires and cables are well insulated, without leakage, and the metal threaded is not rusted, and its damage is close to zero. His steel wire rope should comply with the corresponding configuration requirements, and there is no problem of broken strands and diameter reduction. Of course, the number of broken wires should not exceed the corresponding standard. His pulley movement is very flexible.