BedgoshBooster pipeline pumpThe shock weakened, and businesses’ bearish attitude towards the future market increased

　　The water pump can be used to transport and pressurize clean water without impurities, such as apartment, residence villa water supply, factory water supply, water supply system, drinking water system and water treatment. In short, there are many uses.　　The high-pressure water flows to the space occupied by the original bubble at a very high speed, forming an impact force. The metal surface of the pump was fatigued and damaged by these impacts. Cavitation is caused by air bubble rupture and material stamping due to the difference in air temperature and pressureBedgosh,　　 connection dimension requirements of pump base outlet (requirements for companion flange and diameter, etc.)　　The submersible slurry pump shall be shut down for inspection in time in case of machine problems during operation, and regular maintenance shall be done. The equipment will not be used after burning out,BedgoshVertical multistage centrifugal pipeline pump, which will cause certain economic losses to us.Grimsby,　　Head refers to the energy obtained from the pump by the unit weight of liquid output by the pump, so head refers to the effective energy obtained from the liquid output by the pump in unit time - that is, the effective power of the pump: the equation is PE= ρ GQH (W)= γ QH (W)　　Will be scrapped. In addition, since the length of the long shaft is generally fixed, the installation and use of the slurry pump submersible are troublesome and the application occasions are limited. The submersible slurry pump is developed to adapt to increasingly complex working conditions and facilitate the use of users. Its use mode is more　　Line direction pay attention to the direction of rotation. Then loosen the original compression nut of the bearing box of the slurry pump of the submersible pump, tighten the adjusting screw of the bearing box evenly, and then move the rotor assembly towards the motor. Then it is necessary to check the clearance with a feeler gauge δ, When δ= A (. ~ mm

　　The non service life of the equipment is not as long as possible. If it is not used for a long time, it will not only easily corrode the parts, but also reduce the service life of the parts.　　 before starting, check all circuits and switches to see if their wiring is correct and reliable, then turn them over the ground for ~ minutes (the time should not be too long to avoid damaging parts or burning motor windings), and check whether the motor running direction is correct. If the above problems are not found, it can be started　　 The fan speed of the water pump is too low, and the air pressure and air volume are relatively small, so the heat cannot be dissipated.market price,　　If there is a standby pump, it is better to use two pumps in turn. If the pump is stuck, the pump can only be repaired. A net can be added at the water inlet to prevent too many impurities from entering the pump. In this way, the probability of pump sticking will be much smaller!　　When using the sand pump, be sure to pay attention to the steering divergence between the motor and the pump. The sand pump has an arrow on the pump to mark the main steering. After the power supply is connected, run the pump without load. Check whether the motor operates normally. During operation, be careful not to exceed the bearing on the pump support to avoid　　After that, before starting again, check whether the impeller rolling is normal and whether the bearing assembly compression bolts are tightened, and then start the pump.

　　 Assembly of rotor parts of submersible slurry pump Before assembly, apply a layer of lubricating oil on the mounting surface to protect the shaft hole from damage.How much does it cost?,　　Submersible slurry pump is a kind of pump used in mines. Do you know the effect and form of its shaft seal? Let&#;s have a look.　　In fact, stainless steel is not only advocated in the medical industry,BedgoshDouble suction slurry pump, but also widely used in the water pump industry. The stainless steel submersible pump of denang pump is one of them.　　Yes, summer is the peak sales season. In addition to agricultural applications industrial pumps have also increased in recent years.Bedgosh, the equipment may be burned out. The main reason for this phenomenon is improper operation. How should we prevent the burning out?　　During normal operation　When using the submersible slurry pump, the temperature of the motor is very high, some even as high as ℃. In this case,BedgoshVertical slurry pump, it is easy to burn the motor and replace it with a new one. In fact, one motor burns out at this time. Don&#;t worry about replacing it. You must find out the cause of the motor&#;s heating, or　　There is no need to equip auxiliary mixing or spraying equipment, and the site is cleaner.