Matt BarrySewage pump divingHow was it replaced

　　 one method is to use ultrasonic method to detect whether the equipment has cavitation. This method is often convenient for re detection. Even if there is some noise in the surrounding environment, it will not affect the detection results. Therefore, it must be used continuously during transportation. If there is an interval in the middle, it must be avoided that the interval is relatively long, so as to avoid the solidification of slurry in the pump when the operation is stopped.Matt Barry,　　Check the three-phase current with an ammeter on the control panel. If the phase power supply is found to be insufficient, the power supply of the submersible pump shall be turned off immediately. Check whether the cable connector connection point and power switch contact are in poor contact and whether they are the main line. Check whether the circuit wiring is broken or loose, or whether the fuse is damaged or burnt out　　 If the head of the submersible slurry pump is too low or the head is higher than the practical condition, the flow will be large and the current will rise. At this time, the outlet valve can be turned down to increase the resistance to control the current.Denbica,　　No matter what type of slurry pump you need, Ritter pump will provide you with the highest quality slurry pump products; The latest development of submersible slurry pump technology in recent years The diving depth has increased from meters to meters!　　Water pump After understanding the cause of insufficient liquid supply, we can solve the problem: First, we need to check whether the liquid level of the circulating liquid storage tank needs to add media to it.　　The vertical sand pumping pump is popular with a wide range of sand pumping pump users because it is easy to move. This equipment is made of high-tech endurance data. Its service life has been greatly improved, and the maintenance frequency has been reduced, the cost has been reduced and the income has been increased.

　　The input quantity is related to many factors such as the rotating speed of the submersible slurry pump, the bearing standard, the continuous working time,Matt BarrySubmersible non clogging slurry pump, the number of stops and starts of the pump, the surrounding environment and the working temperature. Therefore, it is necessary to gradually accumulate the experience and add smooth oil in a reasonable and timely manner.　　 still water level of water well M　　 Inspection before installation: Check the specification, size and quality of thick and thin accessories.Direct labor,　　Then there are new structures, such as thermohydrodynamic seals,Matt BarryCentrifugal slurry pump, backup seals and asymmetric molded metal single wall bellows seals.　　 Impeller protection in order to ensure the operation of the submersible slurry pump, first stop the pump, loosen the bolts pressing the bearing box, loosen the adjusting nuts, make the bearing components move forward, and roll the shaft by hand to press the　　For example, it has a great impact on the impeller of the equipment itself. So how to detect whether the equipment has cavitation during use?

　　Most of the time, we don&#;t know how to choose the pump when we buy it. In fact, we only need to choose the appropriate equipment according to our own use needs when we choose it. It&#;s more like that in a conventional family, when we use it, the flow is smallFocus on Development,　　The purpose is to inject liquid higher than . MPa from the water seal ring to prevent gas leakage into the pump when the suction inlet of the submersible slurry pump is in a vacuum state. When the water pressure in the pump is higher than . MPa, the sealing fluid .-. MPa higher than the pressure in the pump can be injected to seal and reduce leakage　　It can be done. For example, before the test run, the motor and the main pump are separated from the test in the positive and negative directions, including glue, etc.　　 for screws that are too tight or rusted for a long time, or the nut can be gently knocked with a wooden hammer and then removed. This method can also be used in slurry pumps and other places.Matt Barry　　After that, before starting again, check whether the impeller rolling is normal and whether the bearing assembly compression bolts are tightened,Matt BarryScrew deep well pump, and then start the pump.　　Strong strength and other advantages. It is widely used as a sealing device for various pumps. Place a water seal ring at the bottom of the packing box, and then place the filler.　　Ordinary vertical motor can be used without waterproof, while the motor shaft and pump shaft of submersible slurry pump are coaxial, so the motor must be waterproof and sealed, and the motor and pump can be immersed in liquid at the same time; The vertical slurry pump is an early product, and the submersible slurry pump is a newly developed product according to the market demand