MandaliQuotation slurry pumpPrecautions for installation and maintenance

　　If the submersible slurry pump cannot be installed and operated, the blank operation point can be supplemented.　　Avoid airborne sound transmission; Ensure the airtightness of machine room doors and windows. The water pump is equipped with a sound proof cover, the inlet and outlet of the sound proof cover are equipped with silencing equipment. A vibration isolation platform is installed at the bottom of the water pump for foundation vibration reduction to isolate the vibration generated during the operation of the water pumpMandali, the supporting pipelines in the pump room shall be provided with vibration isolation elasticity.Joyce difora loading and unloading of electric pump: remove the cable and disconnect the power supply.　　At the same time,MandaliSelf priming non clogging sewage pump,　　Pump, sewage submersible pump and seawater submersible pump.　　With the continuous development of slurry pump technology, submersible slurry pump has also responded to the market demand. At the same time,MandaliIrrigation deep well pump,MandaliVertical slurry pump, this type of pump is especially suitable for the depth where the vertical slurry pump cannot operate. Pay attention when using the equipment. The submersible slurry pump can operate if its depth is less than m, but it exceeds　　 install a valve to inject water at the water inlet and outlet. This method is to install a valve on the water inlet pipe of the submersible slurry pump and connect the water pipe to inject water into the pump. This is a common and simple method.

　　Wheel mixing impeller and other main flow passage parts are made of high wear-resistant raw materials, which are wear-resistant corrosion-resistant, non clogging, and have strong sewage discharge capacity, and can effectively pass through large solid particles. It is not limited by suction range, with high slag suction efficiency and more complete desilting. There is no need to equip auxiliary vacuum pump, and the investment is lower.　　 Long term dehydration operation of submersible sewage pump: since the submersible sewage pump uses water as cooling water, the motor may overheat and burn due to long-term dehydration.　　All kinds of newly designed mechanical seals of submersible slurry pumps contribute greatly to the growth of market share.superior quality,　　The higher the specific speed of submersible slurry pump, the smaller the allowable cutting amount of impeller diameter. In addition to the sealing effect, the auxiliary impeller of the submersible slurry pump can also reduce the axial force.　　 The slurry pump mainly aims at conveying flow, so the flow meter (meter) shall be installed in the operation monitoring system as far as possible to monitor whether the flow meets the requirements at any time; In the pipeline system, slag flushing system and pressure filtration dehydration system equipped with hydrocyclone, certain　　There is a difference between submersible slurry pump and sewage pump. Although the media conveyed by the two are not pure water and other media, the difference between slag slurry and sewage is still large. Let&#;s take a look at the difference between the two.

　　Turn on the power supply type fool operation; It has a wide range of applications. In many cases, it belongs to a portable workstation, which can be brought wherever it is needed, because it does not need too many auxiliary facilities.production, the blank operation point can be supplemented.　　Pipeline pump, belonging to the category of centrifugal pump, is a single-stage centrifugal pump with standing structure. Because the layout design of its water pump inlet and outlet is relatively special, they are all located on the same straight line, and their inlet and outlet diameters are the same, the overall description is similar to a section　　For example, it has a great impact on the impeller of the equipment itself. So how to detect whether the equipment has cavitation during use?Mandali,　　Then there are new structures, such as thermohydrodynamic seals, backup seals and asymmetric molded metal single wall bellows seals.　　 Before starting the submersible slurry pump, the rotor of the rotating pump shall be smooth and even, the outlet sluice valve shall be closed, and water shall be injected into the pump to ensure that the pump is full of water without air.　　 We also need to make choices according to local conditions when we make purchases at ordinary times. For example, the head of the centrifugal pump itself is relatively high, but its water output is not very large when it is used, so it is effective when it is used in many mountainous areas