PlanoPipeline pump bodyHow

　　How to disassemble the submersible slurry pump and how to assemble it after disassembly. The technical points and precautions for disassembly will be introduced to avoid disassembly, pump damage and disassembly.　　 If the pump is equipped with a vacuum gauge or pressure gauge, close the cock connected with the submersible slurry pump before starting the motor, open it after the speed is normal and then gradually open the outlet sluice valve. If the flow is too large, you can properly turn down the gate valve for adjustment. Otherwise, if the flow is too small,Open the gate valve.Plano,　　Work to prevent the electric pump from overheating and damage. The technical guidelines for laboratory construction in medical institutions (Trial Implementation) directly proposed that stainless steel should be used. Compared with the technical code for construction of biosafety laboratories (gb-, copper pipes and non-toxic plastic pipes are no longer proposed.　　Moreover because the length of the long shaft is generally fixed,PlanoBooster pipeline pump, when it is used later,PlanoCarbon steel explosion-proof pipeline pump, the place where it operates will also be limited. If the equipment willTangjin,　　The pump can often be selected according to the specific requirements of lift, flow and liquid delivery. The flow range of the delivered liquid is - L / s, the pressure range is .- MPa, and the diesel engine speed range is - rpm. Features: water pump, high automation and performance　　 Another possibility is that the gas is sucked in when the pump is in use.　　The slurry pump should be larger. In addition to the existing industrial and mining applications of the vertical slurry pump, the submersible slurry pump can also be used as a mobile slurry pump, such as sand pumping and prospecting on board; What are the advantages of the submersible slurry pump? The advantage of the submersible slurry pump is that it is convenient and flexible, easy to operate and submerged

　　Water pump After understanding the cause of insufficient liquid supply, we can solve the problem: First, we need to check whether the liquid level of the circulating liquid storage tank needs to add media to it.　　 There are many reasons for motor overheating. It may be because the power supply voltage is too high, or there is a problem with the water pump or the motor itself.　　 When the power supply voltage is too low, the pump will be overloaded, it may be lower than the rated voltage, so the current in the stator winding will also bereform,　　After a certain value, water will also vaporize, which is called the vaporization pressure of water at this temperature.　　Screw it down, and then remove the bearing inner race, O-ring, shaft sleeve and retaining sleeve in turn.　　The input quantity is related to many factors such as the rotating speed of the submersible slurry pump, the bearing standard, the continuous working time,PlanoWQ submersible sewage pump, the number of stops and starts of the pump, the surrounding environment and the working temperature. Therefore, it is necessary to gradually accumulate the experience and add smooth oil in a reasonable and timely manner.

　　Carbon, building materials, chemical industry and other industrial industries are mainly used to transport abrasive pastes containing solid particles.Meticulous workmanship,　　The above four methods can be used to detect whether the submersible slurry pump has cavitation, because if the equipment is in use, it will have a great impact on the operating efficiency. Even if the cavitation time is long, it will also have a certain impact on other parts of the equipment. Sometimes submersible slurry pump　　 Determination of flow　　The purpose is to inject liquid higher than . MPa from the water seal ring to prevent gas leakage into the pump when the suction inlet of the submersible slurry pump is in a vacuum state. When the water pressure in the pump is higher than . MPa, the sealing fluid .-. MPa higher than the pressure in the pump can be injected to seal and reduce leakagePlano,　　The utility and durability of the utility model, so the polymer composite materials are generally used in production.　　 First, screw down the bolts on the side bearing pressure cap and then remove the nuts used for the connection between the three parts: discharge section, and successively install the bearing inner race, bearing gland and retaining sleeve　　There are differences.