AntwerpBooster pipeline pumpCustomer first

we don&#;t know how to choose the pump when we buy it. In fact

　　Most of the time, we only need to choose the appropriate equipment according to our own use needs when we choose it. It&#;s more like that in a conventional family,AntwerpVertical multistage centrifugal pipeline pump, when we use it, the flow is small　　Whether it is the pre installation inspection or the post installation commissioning inspection, the correct operating procedures must be strictly followed. Only the correct operating steps can make the product play an effective role in the use site.Antwerp, take it out of the water and do not immerse it in the water for a long time, so as to reduce the chance of the motor stator winding getting damp and increase the service life of the electric pump. When the temperature is low, the pump needs to be lifted out to prevent freezing.　　If the shaft seal is not properly selected, it will not only require frequent maintenance during operation, but also leak a large amount of transmitted liquid.San Antonio,　　The packing seal, auxiliary impeller seal and mechanical seal are mainly used. Among them, the packing seal needs small leakage and is not suitable for transporting toxic, corrosive and precious liquids; The sealing of the auxiliary impeller relies on the reverse pressure of the two sealing impellers during rotation to prevent the leakage of the medium,AntwerpWQ submersible sewage pump, and can also play a role in　　After that, the outlet valve of the final stage pump can be gradually opened. The speed of opening the valve should be controlled by the fact that the pump does not vibrate and the motor of any stage does not exceed the rated current.　　The seal cannot bear the water pressure at this depth. Once the water leaks, the motor will not work normally, resulting in damage to the submersible slurry pump. The biggest difference between the submersible slurry pump and the horizontal slurry pump and the vertical slurry pump is that the motor of the submersible slurry pump and the shaft connected to the pump are integrated and sealed Closed.

　　 install a valve to inject water at the water inlet and outlet. This method is to install a valve on the water inlet pipe of the submersible slurry pump and connect the water pipe to inject water into the pump. This is a common and simple method.　　 Check the suction pipe and bottom valve to see if there is any air leakage source. Remove the silt and other obstructions at the water inlet. Check the water inlet depth of the bottom valve to ensure that it is not less than times the diameter of the water inlet pipe. If it is not enough, deepen the water inlet depth of the bottom valve.　When using the submersible slurry pump, the equipment may be burned out. The main reason for this phenomenon is improper operation. How should we prevent the burning out?Excellent quality,　　Most of the time, we don&#;t know how to choose the pump when we buy it. In fact, we only need to choose the appropriate equipment according to our own use needs when we choose it. It&#;s more like that in a conventional family, when we use it the flow is small　　In order to ensure the demand for water and electricity for production and living, many units, hotels and residential areas in various provinces and cities in China have purchased it and generators. Many enterprises have also purchased generators out of their own pockets in order not to delay production. Driven by this, it and the generator naturally become popular　　With water, you can start working.

　　What?quality,　　Then it can enter into the volute pump housing. Then in the volute pump casing, the medium slows down because the flow channel is also gradually expanding.　　 Pipeline booster pump: in fact, any pump that can pressurize the liquid delivered in the pipeline can be called a pipeline booster pump. Not limited to one type of pump,AntwerpAh slurry pump, such as centrifugal pump, pipeline　　There are many types of submersible slurry pumps available in the market and different pump models have different performance and application fields. Therefore, although the pump has a wide range of applications, if its model is not correctly and reasonably selected, its application effect will be greatAntwerp,　　 The difference between the vertical slurry pump and the submersible slurry pump The working position of the vertical slurry pump is different. The vertical slurry pump is partially immersed in the pit and cannot be completely immersed in the liquid level. The submersible slurry pump can be completely immersed (including the motor part) below the liquid level; Use of motor for vertical slurry pump　　It is located in the middle, so it seems that many regions have good effects when using it.　　The high-pressure water flows to the space occupied by the original bubble at a very high speed, forming an impact force. The metal surface of the pump was fatigued and damaged by these impacts. Cavitation is caused by air bubble rupture and material stamping due to the difference in air temperature and pressure